Suzuki 2009 AN400 Supplementary Service Manual Download

Page: 75 / 143

ABS: 4E-33

1) Check that the front wheel speed sensor is mounted

securely.

Is the sensor mounted securely?

Go to Step 4.

Tighten the mounting
bolts.

1) Inspect the front tire and wheel. Refer to “Tire

Inspection” in Section 0B in related manual and “Front
Wheel Related Parts Inspection” in Section 2D in related
manual.

Tire type and size
BRIDGESTONE HOOP B03 G, 120/80-14M/C 58S

Cold inflation tire pressure (Solo riding)
175 kPa (1.75 kgf/cm

, 25 psi)

Cold inflation tire pressure (Dual riding)
175 kPa (1.75 kgf/cm

, 25 psi)

Wheel runout
Service limit (axial and radial): 2.0 mm (0.08 in)

Are the front tire type, tire pressure and wheel runout OK?

Replace the ABS
control unit/HU.

Adjust or replace the
front tire and wheel.

Step

Action

Yes

I905H1450032-01

I905H1450033-01

Summary of Contents for 2009 AN400
















































































































































Search results

Summary of Contents for 2009 AN400

Reviews:

Related manuals for 2009 AN400

Brands by name

Popular brands

Suzuki 2009 AN400, Supplementary Service Manual

Search results

Summary of Contents for 2009 AN400

Reviews:

Related manuals for 2009 AN400

Brands by name

Popular brands