WARMATOWEL is an electrical heating appliance, intended only for indoor residential applications
and, as such, should be installed and used with certain precautions for your safety.
1. INSTALLATION PROCEDURES FOR PERMANENTLY-WIRED WALL-MOUNTED UNITS MUST BE ACCOMPLISHED BY
QUALIFIED PERSONNEL IN STRICT ACCORD WITH APPLICABLE NATIONAL AND LOCAL BUILDING AND ELECTRICAL CODES.
2. DO NOT place WARMATOWEL units inside a shower, sauna or steam room enclosure or any other wet location.
3. CAUTION is advised when WARMATOWEL is accessible to children.
4. For the ultimate ease in use, a dedicated wall switch or timer can be used to control the WARMATOWEL unit.
Contact Sussman-Automatic Corp. for an in-wall 24-hour-7 day timer (PN W-103588) Note: All switches and control
devices must be installed on the load (black) side of the Towel Warmer circuit in compliance with the National Electric
Code and Local Codes. (see page 8 for installation instructions)
READ THIS ENTIRE INSTRUCTION MANUAL THOROUGHLY BEFORE BEGINNING INSTALLATION AND SAVE THESE INSTRUCTIONS.
BE CERTAIN ELECTRICITY IS SHUT OFF AT MAIN PANEL BEFORE WIRING OR SERVICING YOUR
WARMATOWEL. Follow instructions to make certain your WarmaTowel is properly attached
to the wall. FAILURE TO FOLLOW THESE STEPS COULD RESULT IN HAZARDOUS CONDITIONS.
To avoid possible fire hazard, the WarmaTowel must remain in its intended position.
MOUNT THIS UNIT ONLY AS SHOWN IN THESE INSTRUCTIONS.
TO ENSURE CORRECT OPERATION OF YOUR WARMATOWEL, PLEASE FOLLOW ALL THE INSTRUCTIONS CAREFULLY,
OBSERVING THE "CAUTION" NOTATIONS FOR EACH STEP.
IMPORTANT:
The finish of your WarmaTowel can be protected and maintained by an occasional wiping with a soft,
non-abrasive, damp cloth and lightly polished, thereafter, with a soft dry cloth when the WarmaTowel is cold. Under no
circumstances should abrasive cleaning powders, metal polish or chlorine-based cleaners be used on any part of this product.
IMPORTANT:
This appliance is intended for towels washed in water. Fabrics that contain soap or detergent residue
may show what appears to be scorch marks. However this is simply the discoloration of the residue. The WarmaTowel unit
does not reach sufficient temperature to scorch fabric.
We are not responsible for discoloring or scorching of any fabrics.
THANK YOU
for selecting WARMATOWEL, the perfect addition to bathrooms, family spas, and exercise rooms
within your home. Our products have long been a standard for quality and comfort, and we are sure that you will
experience continued enjoyment from the WARMATOWEL you have purchased by following these simple instructions.
1
WARMATOWEL SPECIFICATIONS
_______________________________________________________________
Model No. Dimensions
Amps
Volts/Phase Weight (lbs.)
______________________________________________________________
W500
24 x 22.5 x 5
1.25
120/1
16
______________________________________________________________
W510
18 x 20.5 x 5
1.25
120/1
14
______________________________________________________________
W542
26 x 23 x 5
1.67
120/1
18
______________________________________________________________
W552
25.5 x 23 x 5*
1.67
120/1
28
______________________________________________________________
W554
21.5 x 23 x 5*
1.67
120/1
22
______________________________________________________________
W556
34 x 23 x 10
1.67
120/1
21
______________________________________________________________
*Add 10" for shelf width. All dimensions are in inches. ALL UNITS 120 VOLTS.
Inspect WarmaTowel
A. Unpack the Towel Warmer carefully to avoid any
damage or loss of any part. When opening the
box be sure that the parts are not accidentally
discarded. WarmaTowels are shipped in specially
designed shipping cartons. The entire surface of
the WarmaTowel is hand-wrapped to protect the
finish. It is your responsibility to immediately
inspect for any damage.
WARNING
!
WARNING
!
WARNING
!
WarmaTowel
Installation and Operating Instruction
®
