background image

17

18

WARNING

It is normal to trigger tilt switch of the power system if bike tip-over 
occur when riding (power output is cut off, and it can be recovered 
after righting the bike again). For your safety, please ensure to turn 
off the key switch before lifting the bike to avoid accidentally twist the 
throttle and cause serious injury.

WARNING

Please make sure to turn off the key switch when parking, to avoid 
accidentally twist the throttle and cause serious injury. Turn off the 
key switch and remove the key before leaving the bike.

Be cautious and ride slow in complex road conditions.

It is prohibited to carry people or items on the bike.

Do not ride when you are tired or in extreme weather.

Do not ride in the water, otherwise it may damage the battery or even cause personal 
injury. 

Please hold the handlebars with both hands and do not ride overspeed.

Slow down before turning.

Do not use mobile phone, camera, earphone, earplug, etc during riding.

●When riding, sudden excessive braking of the right front brake lever may lead to roll over.
●When riding, sudden excessive braking of the left rear brake lever may lead to skid.

Pay  attention  to  the  road  condition,  slow  down  the  bike  while  approaching  the  parking 
spot. When the bike stops, turn off the key switch and remove the key. Flip down the side 
stand to support the bike.

Parking 

Well Prepared Before Riding

      Please make sure that you have fully read all the details in p03 
Chapter 1 Safety Tips and check the following items carefully.          

Check Tires

 

Make sure both tires are in good conditions.
Normal tire pressure is 32.6 psi (225 kPa). Low tire pressure will lead to abnormal wear, 
poor steering, lower speed, and shorten the range.
Extreme high tire pressure will lead to abnormal wear, poor riding experience, and even tire 
explosion.

Check Instrument, Horn, and Brakes

 

Check if all functions of the instrument are displayed normally.
Check if the horn works properly.
Hold the left and right brake levers respectively to check if the front and rear brakes work 
normally.

Check Handlebars

 

Handlebars need to be fixed tighten and turn freely.

Adjust Shock Absorbers

 

Please adjust the front and rear shock absorbers according to the actual situations. 

The bike’s power is cut off (When the power is on but motor not running)

● Side stand switch (with the side stand is down, there will be no power output when 

turning the throttle.)

●tilt switch (1-2 seconds after the bike falls over, tilt switch will cut the power output)

● Motor overheating

● Battery overheating

● Low Battery capacity

● Controller overheating

General Operation 

Summary of Contents for Light Bee QL3000DY



















Reviews: