Surge master SM32S Operator'S Manual Download Page 3

3

WARRANTY

WARRANTY

Effective on products retailed on or after September 1, 2011. 

 

Register your product online at 

www.surgemaster.ca 

within 30 days of purchase to activate warranty.

This product is warranted to be free of defects in materials and workmanship under normal use and service, for a period of 

from the date of purchase, when operated and maintained in accordance with the Operating and Maintenance Instructions 
supplied with this unit.  Warranty is limited to the repair of the product and/or replacement of parts.

This warranty does not cover the following items:

1) Parts lost or damaged during shipment,
2) Normal maintenance or adjustments
3) Normal replacement of service items.
4) Accessory items / parts not supplied by EMB MFG INC.
5) Damages resulting from:

•  misuse, negligence, accident, theft or fire
•  use of improper or insufficient fuel, fluids or lubricants 
•  use of parts or after market accessories other than genuine EMB MFG INC. parts  
•  modifications, alteration, tampering or improper repair performed by parties other than an authorized servicer
•  any device or accessories installed by parties other than an authorized EMB servicer

Engines are covered by the manufacturer of the engine and covered by the warranty period specified by that manufacturer.  

Engine warranty must be registered at the engine manufactures website. 

For service contact your local engine dealer.  

Under no circumstances will the manufacturer be liable for any consequential damage or expense of any kind, including loss 
of profits.  The manufacturer is under no circumstances liable for tow vehicle of any kind.  The manufacturer is not liable for 
the maintenance of the product.

This warranty is extended only to the original purchaser and is not transferable.  Warranty is void if repairs are attempted by 
anyone other than an authorized service centre.

If a difficulty develops with the product, contact EMB MFG INC.  Only our authorized service centres may make repairs to 
the product or affect the replacement of defective parts, which will be done at no charge within a reasonable time after the 
receipt of the product.  Unit or parts shall be returned at the customer’s expense to the authorized service centre.  Damage 
in transit is not covered by warranty.  

Include the original purchase receipt with any claim

 (keep a copy of the receipt 

for your files).

The distributor’s liability under warranty is limited to the repair of the product and/or replacement of parts and is given to the 
purchaser in lieu of all other remedies including incidental and consequential charges.  There are no warranties, expressed 
or implied, other than those specified herein.
  

EMB MFG Inc

4144 Boomer Line, St Clements, ON  N0B 2M0  Canada

Phone:  519-699-9283  Fax:  519-699-4146 : attention to Warranty Dept

Email:  [email protected] 

WARRANTY IS VOID IF NOT REGISTERED

Three (3) Years for Consumer

One (1) Year for Commercial/Rental 

rev.091111

Summary of Contents for SM32S









































Reviews: