manualshive.com logo in svg

SureShade 2020134625, Installation And Owner'S Manual

Share
Download
SureShade 2020134625 Installation And Owner'S Manual Download Page 11

11

lci1.com      

 

574-537-8900    

 

Rev: 01.05.21

SureShade

®

 

Power Bimini  

Sport Arm Kit

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0003954

5. 

Repeat steps 1-3 on the second front frame.

Operation

Extend the Front Sport Arms

To extend the front sport arms, do as follows:

NOTE: 

Maximum speed rating of front sport arms 

is 45 MPH.

1. 

Fully open the Power Bimini top until the auto-reset 

breaker trips.

2. 

Pull the front sport arm out of its EZ Clip.

3. 

Position the swivel barrel over the hinge assembly.

Fig.22 

MAXIMUM SPEED RATING WITH FRONT SPORT 

ARMS IN USE IS 45 MPH.

IF EXCESSIVE SHAKING OF THE BIMINI TOP IS 

EXPERIENCED, WHETHER THE FRONT SPORT 

ARMS ARE IN USE OR NOT, STOP THE BOAT 

IMMEDIATELY. LOWER THE BIMINI TOP AND 

SECURE WITH BOOT.

4. 

Slide and hold the locking button down, then insert the 

swivel barrel. See figure 12.

5. 

Release the locking button.

4. 

Using an electric or cordless drill or screw gun and a 

Phillips head drive bit, insert the 

3/16

” self-drilling screw 

(Fig.22A)

 through the EZ Clip’s center hole and tighten.

EZ clip

 A

IF EXCESSIVE SHAKING OF THE BIMINI TOP IS 

EXPERIENCED, WHETHER THE FRONT SPORT 

ARMS ARE IN USE OR NOT, STOP THE BOAT 

IMMEDIATELY. LOWER THE BIMINI TOP AND 

SECURE WITH BOOT.

Retract the Front Sport Arms

To retract the front sport arms, do as follows:

1. 

Slide and hold the hinge assembly’s locking button 

down, then pull the swivel barrel out of the locking plate. 

See figure 19.

2. 

Release the locking button.

3. 

Push the front sport arm into its EZ Clip 

(Fig.23)

.

Fig.23 

EZ clip

front support

front frame

locking plate

Summary of Contents for 2020134625













Reviews:

No comments

Brands by name

Popular brands

Load more brands