manualshive.com logo in svg

SurePoint Sentinel NH3, Installation And Setup, Page: 9 / 36

Share
Download
SurePoint Sentinel NH3 Installation And Setup Download Page 9

 

396-4519Y1   Sentinel NH3 Blockage Monitor 

 6 

Revised 01/26/2022 

 

© 2016-2022 SurePoint Ag Systems Inc. 

General Description

 

You have purchased a  SurePoint Sentinel NH3 blockage system for your equipment.  This 

system will be controlled by the Sentinel ECU through your in-cab ISO display.  Your 

anhydrous system will continue to function as usual with application rates being regulated 

by your existing rate controller. The Sentinel NH3 works independently, monitoring the row-to-row accuracy 

of your system and alerting the operator of blocked rows. 

 

SurePoint currently supports Sentinel operating on the following displays:  

John Deere 

2630 & 4640, 

Ag 

Leader

 InCommand 800 and 1200, 

Case IH 

Pro 700, 

Trimble 

Fm2050 and FMX1000.  The use of Sentinel 

NH3 on any other display may result in diminished functionality. 

 

A 2-pin Molex power and 12-pin Ampseal Power/CAN connector are required on your implement to connect 

the Sentinel ECU to the implement bus.  While some equipment manufacturers already provide this 

connection, SurePoint offers harnessing to provide this connection on any implement.  Ask your SurePoint 

representative what accommodations may be needed for your specific equipment. 

A 

Introduction 

Basic Installation Steps

 

1.  Install all Row sensors using the guidelines laid out in the Applicator Plumbing Requirements section on 

page 7. 

2.  Locate the 2-pin Molex power and 12-pin Ampseal POWER/CAN connectors (typically next to the rate 

controller) that the Sentinel ECU will be connected to and remove the terminator.  If you can’t identify 

these connectors, call SurePoint.  Save the terminator for Step 5. 

3.  Mount the Sentinel ECU using the provided bracket in a location within 4 feet of the above connection. 

4.  Attach the ECU harness (208-06-3536Y2) to the Sentinel ECU and plug the other end of the harness into 

the above Molex/Ampseal POWER/CAN connection. 

5.  Use the previously removed terminator to terminate the POWER/CAN connection found on the ECU 

harness. 

6.  Mount the SurePoint NH3 Temperature Interface module (226-01-4210Y1) to the back of the ECU 

bracket used in step 2. 

7.  Plug the 4-pin  Deutsch connector on the temperature interface module into the Flowmeter Bus 1. 

8.  Unplug the 3-pin Weather Pack dust plug that is connected to the temperature interface module and save. 

9.  Use a 3-pin Weather Pack extension cable (206-03-XXXX) to connect the temperature interface module 

to the row sensor mounted on Row 1.   

10. Make sure all row sensors are daisy chained together, using 3-pin Weather Pack extension cables to get 

from NH3 manifold to NH3 manifold. 

11.  Install the 3-pin Weather Pack dust cover removed in step 8 and install it on the last row. 

SurePoint 

Ag 

Systems

Summary of Contents for Sentinel NH3





































Reviews:

No comments