background image

IMPORTANT: For natural gas, check gas line
pressure before connecting heater to gas line.
Gas line pressure must be no greater than
10.5" of water. If gas line pressure is higher,
heater regulator damage could occur.

For propane/LP gas, the installer must supply
an external regulator. The external regulator 
will reduce incoming gas pressure. You must 
reduce incoming gas pressure to between 11" 
and 14" of water. If you do not reduce incoming 
gas pressure, heater regulator damage could 
occur. Install the external regulator with the 
vent pointing down as shown in Figure 13. 
Pointing the vent down protects it from freezing 
rain or sleet.

* An CSA design-certifi ed equipment shutoff
valve with 1/8" NPT tap is an acceptable al-
ternative to test gauge connection. Purchase
the optional CSA design-certifi ed equipment
shutoff valve from your dealer. 

12

Figure 13 - External Regulator With Vent 

Pointing Down

Figure 14 - Gas Connection

INSTALLATION

Continued

       WARNING: This appliance requi-
res a 3/8” NPT (National Pipe Thread) 
inlet connection to the pressure 
regulator.

       WARNING: A qualifi ed service
person must connect heater to gas 
supply. Follow all local codes.

       WARNING: For natural gas, never 
connect heater to private (non-utility) 
gas wells. This gas is commonly 
known as wellhead gas.

     CAUTION: For propane/LP gas, 
never connect heater directly to 
the propane/LP supply. This heater 
requires an external regulator (not 
supplied). Install the external regulator 
between the heater and propane/LP 
supply.

     CAUTION: Use only new, black 
iron or steel pipe. Internally-tinned 
copper tubing may be used in certain 
areas. Check your local codes. Use 
pipe of large enough diameter to allow 
proper gas volume to heater. If pipe is 
too small, undue loss of volume will 
occur.

7"

5/8"

Summary of Contents for BWH10NLM































Reviews: