background image

 

 

 

 Page 

 

3

 

Installation  

 

3.1

 

Safety Precautions 

The Prophet

 uses Radio Frequency (RF) waves for communication to the nearest 

cellular tower and can transmit at several times the power of a hand-held cellular phone.  
In general, if you can place a cellular telephone call in the location where you wish to 
install the unit, then the Prophet should be able to communicate properly.  However, 
because of the inherent characteristics of RF communications, there are certain guidelines 
that should be followed when positioning the unit. 
 

WARNING! 

 

Do not 

use the Prophet

 in hospitals or near medical equipment. 

 

Do not

 install the Prophet

 where hazardous vapors are present. 

 

Do not

 use the Prophet

 where blasting is in progress. 

 

Electrostatic discharge can damage sensitive electronic components. Be sure to 
discharge yourself by touching a grounded metal object before opening the unit. 

 

The unit should be installed in an area free from overhanging metal structures, large 
obstructions, or equipment which could generate RF or electrical interference. 

 

Do not

 install the unit below ground level unless provisions are made for an external 

antenna. 

 

Service may be limited in areas that do not have GSM cellular coverage and support

 

SMS (Short Message Service). 

 

If the unit is installed in an area with poor signal strength, an external antenna may be 
required for reliable performance.  If you have doubt about the suitability of a 
particular location for the Prophet

, or are having difficulty transmitting, please see 

Sections 3-2 and 3-3.  If an external antenna is required, several optional antennas are 
available. Please contact SupplyNet Customer Service to determine your exact needs. 

3.2

 

 Initial Inspection 

When you receive the Prophet

 unit, thoroughly inspect it for any damage which may 

have occurred during shipping.  If there is any damage to the Prophet

, contact the 

shipping company as soon as possible.  Locate the packing checklist in the shipping 
container.  Check for any missing items before you begin installation of the Prophet

 

Note:

 

The Prophet

 is shipped with the antenna disconnected.  It is located in a 

separate area within the shipping carton.  Verify that the antenna is present 
before proceeding. 

 

Tools Required for Installation: 

 

3/16” Flat screwdriver 

 

Large adjustable wrench 

Summary of Contents for Prophet 4000 Series


































Reviews: