background image

14 
 

Terms & Conditions 

 

Dealer, warrants to the original consumer purchaser that each new SuperStick® EXP 42” Plus 
laminator which proves defective in materials or workmanship within the applicable warranty period 
will be repaired or at our option, replaced without charge upon its return as outlined below.  The 
applicable warranty shall be one year from date of purchase.  “Original consumer purchaser” means 
the purchaser who first purchased the product covered by this warranty other than for purpose of 
resale. 
 
Liability for breach of any warranty expressed or implied shall be limited to the repair or replacement, 
at the dealer’s discretion of the defective item.  The dealer shall not be liable for damages arising out 
of, or in connection with the use or performance of any SuperStick® product.  Any implied warranty 
shall be limited in duration to the duration of this warranty.  Some states do not allow limitations on 
how long an implied warranty lasts for the exclusion or limitation of consequential damages, so the 
above limitation may not apply to you. 
 
There are no consumer serviceable parts in the SuperStick® EXP 42” Plus laminator.  If you require 
service under this warranty, contact your dealer to obtain a return authorization number (RA), pack 
the product in its original packaging (or request the same from technical service when requesting the 
RA), and include a description of the malfunction and proof of the date of purchase. Technical service 
will arrange for the SuperStick® EXP 42” Plus laminator to be picked up by a freight company. Failure 
to return the laminator in its original packaging could void this warranty. 
 
The warranty extends to and is enforceable only by the original consumer purchaser, and only for the 
period which the product remains in the possession of the original equipment purchaser.  This 
warranty does not cover any defect or malfunction due to the use of faulty non-SuperStick® EXP 42” 
Plus laminator materials, unreasonable use or abuse of the machine, or failure to provide reasonable 
and necessary maintenance.  This warranty gives you specific legal rights and you may have other 
rights, which vary, from state to state. 

 

 

 

 

 

 

 

 

 

 

 

 

Laminator.com

www.laminator.com

Summary of Contents for EXP 42" Plus





















Reviews: