Supero 2U Twin3 SuperServer 2015TA-HTRF User Manual Download

Page: 57 / 94

Chapter 6: Advanced Chassis Setup

6-3

Fan Con

ﬁ

guration

In the 2U Twin

, each node (serverboard) controls the fans that reside on its side

of the chassis. This means that four nodes will share control for two fans. If the

fan speed settings in BIOS are different for these two nodes, the BIOS setting with

the higher fan speed will apply. In the event that one of the serverboard drawers is

removed, then the remaining nodes/serverboards will operate both fans.

Note:

Due to this con

ﬁ

guration, all nodes on the same side of the chassis as the

failed fan must be powered down before replacing the fan.

System Fan Failure

If a fan fails, the remaining fans will ramp up to full speed and the overheat/fan fail

LED on the control panel will blink on and off (about once per second). Replace

any failed fan at your earliest convenience with the same type and model. See

note above about powering down the nodes associated with the failed fan before

replacing.

Changing a System Fan

If necessary, open the chassis while the power is running to determine which

fan has failed. (Never run the server for an extended period of time with the

chassis cover open.)

Remove the failed fan's wiring from the backplane.

Lift the fan up and out of the chassis.

Place the replacement fan into the vacant space in the housing while making

sure the arrows on the top of the fan (indicating air direction) point in the

same direction as the arrows on the other fans.

Con

ﬁ

rm that the fan is working properly before replacing the chassis cover.

Summary of Contents for 2U Twin3 SuperServer 2015TA-HTRF































































































Search results

Summary of Contents for 2U Twin3 SuperServer 2015TA-HTRF

Reviews:

Related manuals for 2U Twin3 SuperServer 2015TA-HTRF

Brands by name

Popular brands

Supero 2U Twin3 SuperServer 2015TA-HTRF, User Manual

Search results

Summary of Contents for 2U Twin3 SuperServer 2015TA-HTRF

Reviews:

Related manuals for 2U Twin3 SuperServer 2015TA-HTRF

Brands by name

Popular brands