Supermicro X9DRG-O-PCIE, User Manual, Page: 64 / 119

2-34
X9DRG-O(T)F-CPU/X9DRG-O-PCIE Platform User’s Manual
SW1
JPW10
J21
SP1
JBT1
JITP0
JSD2 JSD1
JTPM1
I_SA
TA1 I-SA
TA0 I-SA
TA2 I_SA
TA3
JF1
JWD1
JBR1
JPME1
JPL1
JPG1 J29
JPB1
J30
LE1
LE4
DM1
FAN8
FAN6
FAN7
FAN5 FAN1
FAN3
FAN4
JSPK1
JL1
JOH1
JPLD1
JPW18
JPW17
JPW6
JPW12 JPW4 JPW5
JPW3
JPW13
JPW14 JPW15 JPW16 T-SGPIO2
T-SGPIO1
T-SGPIO-S1
BT1
JPW24 JPW23 JPW22 JPW21
BIOS
LICENSE
10G MAC CODE
10G SAN MAC
1G MAC CODE
IPMI CODE
BAR CODE
P2-DIMME1 P2-DIMME2 P2-DIMME3 P2-DIMMF1 P2-DIMMF2 P2-DIMMF3
USB10/1
1
USB2/3
CPU1
P1-DIMMC1 P1-DIMMC2 P1-DIMMC3 P1-DIMMD1 P1-DIMMD2 P1-DIMMD3
LAN2 LAN1
CPU2
P1-DIMMB3
P1-DIMMB2
VGA1
P1-DIMMB1
P2-DIMMH3
COM1
P1-DIMMA3 P1-DIMMA2
P2-DIMMH2
P1-DIMMA1
P2-DIMMH1
IPMI_LAN
P2-DIMMG3
USB0/1
P2-DIMMG2 P2-DIMMG1
REV:1.00
X9DRG-OF-CPU
S_SA
TA1
FAN2
JPW7
I_SA
TA4 I_SA
TA5
S_SA
TA2 S_SA
TA2 S_SA
TA3
JPME2
CLOSE 1st
OPEN 1st
CLOSE 1st
OPEN 1st
USB8/9
PCH
BIOS
LAN
CTRL
BMC
BMC Firmware
CLK Chip
USB6
J34 J33
J32
J31
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note 1:
For an ATX power supply, you must completely shut down the
system, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2: Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3: Clearing CMOS will also clear all passwords.
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD1) is a system monitor that will re-
boot the system when a software application hangs.
Close pins 1-2 to reset the system if an application
hangs. Close pins 2-3 to generate a non-maskable
interrupt signal for the application that hangs. See
the table on the right for jumper settings. Watch
Dog must also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Definition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled
B
A