Supermicro SUPERSERVER 6014P-32 User Manual Download Page 79

Page: 79 / 126

Chapter 7: BIOS

7-13

Base I/O Address

Select the base I/O address for COM2. The options are 3F8/IRQ4,

2F8/IRQ3

3E8/IRQ4 and 2E8/IRQ3.

Floppy Disk Controller

This setting allows you to assign control of the ﬂ oppy disk controller. The options

are

Enabled

(user deﬁ ned), Disabled, and Auto (BIOS and OS controlled).

Base I/O Address

Select the base I/O address for the parallel port. The options are

Primary

and Secondary.

DMI Event Logging

Access the submenu to make changes to the following settings.

Event Log Validity

This is a display to inform you of the event log validity. It is not a setting.

Event Log Capacity

This is a display to inform you of the event log capacity. It is not a setting.

View DMI Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Event Logging

This setting allows you to

Enable

or Disable event logging.

ECC Event Logging

This setting allows you to

Enable

or Disable ECC event logging.

Mark DMI Events as Read

Highlight this item and press <Enter> to mark the DMI events as read.

Clear All DMI Event Logs

Select Yes and press <Enter> to clear all DMI event logs. The options are Yes

and

Summary of Contents for SUPERSERVER 6014P-32































































































































Search results

Summary of Contents for SUPERSERVER 6014P-32

Reviews:

Related manuals for SUPERSERVER 6014P-32

Brands by name

Popular brands

Supermicro SUPERSERVER 6014P-32, User Manual

Search results

Summary of Contents for SUPERSERVER 6014P-32

Reviews:

Related manuals for SUPERSERVER 6014P-32

Brands by name

Popular brands