Supermicro SUPERSERVER 6014P-32 User Manual Download Page 101

Page: 101 / 126

Appendix B: Software Installation

B-9

For RAID 0, select the desired stripe size. (*Note: Available stripe sizes

are 16, 32, and 64 KB-default. It is recommended that you

do not

change the

default

setting.)

4. The item:

"Create RAID via"

allows you to select between the different creating

methods for RAID 0 and RAID 1.

The following table gives examples of when each is appropriate.

Raid Level

Create Via

When Appropriate

RAID 0

No Init

Creating a RAID 0 on new drives

RAID 0

Migrate
(*Note)

Creating a RAID 0 from one new drive and
one drive with data you wish to preserve

RAID 1

Build1

Any time you wish to create a RAID 1, but especially if
you have data on one drive that you wish to preserve

RAID 1

Clear

Creating a RAID 1 on new drives, or when you want to
ensure that the array contains no data after creation.

RAID 1

Quick

RAID 1

Init

Fastest way to create a RAID 1.
Appropriate when using new drives

Note:

If you select Migrate for RAID 0, or Build for RAID 1, you will be asked

to select the source drive. The contents of the source drive will be preserved.

However, the data on the new drive will be lost.

When you are ﬁ nished, press

Done (as the screen shown below)

Summary of Contents for SUPERSERVER 6014P-32































































































































Search results

Summary of Contents for SUPERSERVER 6014P-32

Reviews:

Related manuals for SUPERSERVER 6014P-32

Brands by name

Popular brands

Supermicro SUPERSERVER 6014P-32, User Manual

Search results

Summary of Contents for SUPERSERVER 6014P-32

Reviews:

Related manuals for SUPERSERVER 6014P-32

Brands by name

Popular brands