Supermicro SuperServer 510P-WT/WTR User Manual Download

Page: 39 / 113

Chapter 3: Maintenance and Component Installation

BIOS

LICENSE

BAR CODE

IPMI CODE

MAC CODE

SAN MAC

DESIGNED IN USA

X12SPW-TF/F

REV: 1.10

JNCSI1

S-SGPIO1

JBT1

JPWR2

JSD2

JSD1

S-SA

TA1

S-SA

TA0

JSTBY1

JRK1

JPWR3

JPWR1

JF1

JVRM2

JVRM1

JPFR3

JPFR2

JPFR1

JL1

JD1

JPRG1

JWD1

JP4

FAN6

FAN7

FAN4

FAN3

FAN5

FAN1

BT1

NVME0/1

NVME2/3

MH16

MH15

JPI2C1

JI2C_EXP1

JNVI2C

JIPMB1

MH4

MH6

MH1

MH9

MH5

MH3

MH2

JPME1

SXB2: PCI-E 4.0 X16

SXB1A

SXB1B: PCI-E 4.0 X16 + X16

SXB1C

COM2

LEDBMC

I-SATA4~7

M.2-H

COM1

DIMMG1

DIMMH1

DIMME1

DIMMF1

DIMMA1 DIMMB1

DIMMD1

DIMMC1

CPU

USB6/7(3.0)

USB4/5(3.0)

USB2/3

LAN2

LAN1

CMOS CLEAR

I-SATA0~3

TPM/POR

T80

UID-SW

UID-LED

VGA

USB0/1

IPMI_LAN

USB8(3.0)

FAN2

DIMM Installation

1. Insert the desired number of DIMMs

into the memory slots based on the

recommended DIMM population table on

page 37.

2. Push the release tabs outwards on both

ends of the DIMM slot to unlock it.

3. Align the key of the DIMM module with the

receptive point on the memory slot.

4. Align the notches on both ends of the

module against the receptive points on the

ends of the slot.

5. Press the ends of the module straight

down into the slot until the module snaps

into place.

6. Press the release tabs to the lock positions

to secure the DIMM module into the slot.

DIMM Removal

Press both release tabs on the ends of the
DIMM module to unlock it. Once the DIMM
module is loosened, remove it from the
memory slot.

Release Tabs

Notches

Press both ends
straight down into
the memory slot.

Summary of Contents for SuperServer 510P-WT/WTR


















































































































Search results

Summary of Contents for SuperServer 510P-WT/WTR

Reviews:

Related manuals for SuperServer 510P-WT/WTR

Brands by name

Popular brands

Supermicro SuperServer 510P-WT/WTR, User Manual

Search results

Summary of Contents for SuperServer 510P-WT/WTR

Reviews:

Related manuals for SuperServer 510P-WT/WTR

Brands by name

Popular brands