Supermicro SuperServer 1025C-3 User Manual Download Page 75

Page: 75 / 110

Chapter 7: BIOS

7-3

Main BIOS Setup Menu

Main Setup Features

System Time

To set the system date and time, key in the correct information in the appropriate

fi elds. Then press the <Enter> key to save the data.

System Date

Using the arrow keys, highlight the month, day and year fi elds, and enter the correct

data. Press the <Enter> key to save the data.

BIOS Date

This fi eld displays the date when this version of BIOS was built.

Legacy Diskette A

This setting allows the user to set the type of fl oppy disk drive installed as diskette A.

The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in,

1.44/1.25MB

3.5 in and 2.88MB 3.5 in.

Summary of Contents for SuperServer 1025C-3















































































































Search results

Summary of Contents for SuperServer 1025C-3

Reviews:

Related manuals for SuperServer 1025C-3

Brands by name

Popular brands

Supermicro SuperServer 1025C-3, User Manual

Search results

Summary of Contents for SuperServer 1025C-3

Reviews:

Related manuals for SuperServer 1025C-3

Brands by name

Popular brands