Chapter 7: AMI BIOS
7-21
7-20
SUPERSTORAGESYSTEM SSG-2028R-DN2R20L User's Manual
sSATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
OPROM for system boot. The options are Disabled, EFI, and
Legacy.
SATA/sSATA RAID Boot Select
Select SATA Controller to boot the system from a SATA RAID device. Select sSATA
Controller to boot the system from a sSATA RAID device. Select Both to boot the
system either from a SATA RAID device or from an sSATA RAID device. Please
note that the option-Both is not supported by the Windows Server 2012/R2 OS.
The options are Both, SATA Controller, and
sSATA Controller
.
sSATA Port 0 ~ Port 3 Hot Plug
Select Enabled to enable hot-plugging support for a port specified by the user,
which will allow the user to replace a sSATA disk drive installed on this port
without shutting down the system. The options are
Enabled
and Disabled.
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE-
SET initialization to the device. The options are Enabled and
Disabled
.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be con-
nected to a Solid State drive or a Hard Disk Drive. The options are
Hard Disk
Drive
and Solid State Drive.
Server ME (Management Engine) Configuration
This feature displays the following system ME configuration settings.
•
General ME Configuration
•
Operational Firmware Version
•
ME Firmware Type
•
Recovery Firmware Version
•
ME Firmware Features
•
ME Firmware Status #1
•
ME Firmware Status #2
•
Current State
•
Error Code
PCIE/PCI/PnP Configuration
The following items will display:
•
PCI Bus Driver Version
•
PCI Devices Common Settings
PCI PERR/SERR Support
Select Enabled to support PERR (PCI/PCI-E Parity Error)/SERR (System Error)
runtime error reporting for a PCI/PCI-E slot. The options are Enabled and
Disabled
.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and
Disabled
.
SR-IOV (Available if the system supports Single-Root Virtualization)
Select Enabled for Single-Root IO Virtualization support. The options are Enabled
and
Disabled.
Maximum Payload
Select Auto for the system BIOS to automatically set the maximum payload value
for a PCI-E device to enhance system performance. The options are
Auto
, 128
Bytes, and 256 Bytes.
Maximum Read Request
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are
Auto
,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
ASPM Support
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are
Disabled
and Auto.
Warning
: Enabling ASPM support may cause some PCI-E devices to fail!
MMIOHBase
Use this item to select the I/O base memory size according to memory-address
mapping for the PCH chip. The base memory size must be between 4032G to
4078G. The options are
56TB
, 40TB, 24T, 3T, 2T, and 1TB.
Summary of Contents for SSG-2028R-DN2R20L
Page 1: ...User s Manual Revision 1 0 SuperStorageSystem SSG 2028R DN2R20L ...
Page 29: ...4 20 SUPERSTORAGESYSTEM SSG 2028R DN2R20L User s Manual Notes ...
Page 74: ...7 42 SUPERSTORAGESYSTEM SSG 2028R DN2R20L User s Manual Notes ...
Page 76: ...A 2 SUPERSERVER SSG 2028R DN2R20L User s Manual Notes ...
