Supermicro MicroBlade MBM-GEM-004 Web User Manual Download Page 127

Page: 127 / 164

Release: 1.0

127 / 164

MBM-GEM-004 Switch Web User Guide

Received CRC –

Number of packets received with CRC errors.

Received Discards

- Number of packets discarded due to errors.

Received Errors

- Number of packets received with errors.

Received Unknown Protocols

- Number of packets received with unknown protocol.

Transmitted Octets

- Number of bytes transmitted.

Transmitted Unicast Packets

- Number of unicast packets transmitted.

Transmitted Unicast Packets

Rate

- Number of unicast packets rate transmitted.

Transmitted Multicast Packets

- Number of multicast packets transmitted.

Transmitted Multicast Packets

Rate

- Number of multicast packets rate transmitted.

Transmitted Broadcast Packets

- Number of broadcast packets transmitted.

Transmitted Broadcast Packets

Rate

- Number of broadcast packets rate transmitted.

Transmitted Total Packets

Rate

- Number of total packets rate transmitted.

Transmitted Pause

- Number of pause packets transmitted.

Transmitted Discards

- Number of packets discarded due to transmit errors.

Transmitted Errors

- Number of transmit errors.

Reset Statistics –

This button used to reset the received and transmitted packet counter values

to 0.

Summary of Contents for MicroBlade MBM-GEM-004





































































































































































Search results

Summary of Contents for MicroBlade MBM-GEM-004

Reviews:

Related manuals for MicroBlade MBM-GEM-004

Brands by name

Popular brands

Supermicro MicroBlade MBM-GEM-004, Web User Manual

Search results

Summary of Contents for MicroBlade MBM-GEM-004

Reviews:

Related manuals for MicroBlade MBM-GEM-004

Brands by name

Popular brands