•
This appliance is an Inset Decorative Fuel Effect appliance which provides radiant warmth utilising the latest type burner technology.
•
The fire is designed to suit various types of fireplaces and natural draught flues as detailed in this manual.
•
The appliance must be installed by a competent person in accordance with Gas Safety (Installation and Use) Regulations 1998. It is
strongly recommended that a GAS SAFE registered engineer be used for this purpose.
•
Read all these instructions before commencing installation.
•
This appliance must be installed in accordance with the rules in force and used only in a sufficiently ventilated space.
•
The appliance is designed for installation on to a non-combustible hearth of at least 300mm depth.
•
This appliance is factory set for operation on the gas type, and at the pressure stated on the appliance data plate.
•
In the event of gas leakage from the appliance, the gas supply must be turned off at the nearest isolating valve.
•
The appliance must be installed in accordance with the following:
•
Failure to comply with the above could lead to prosecution and deem the manufacturer’s warranty invalid.
•
The appliance is designed to fit various types of situations as described in sections 3.0 and 4.0.
•
It should be noted that heaters create warm air currents. These currents move heat to wall surfaces next to the heater. Installing the
heater next to vinyl or cloth wall coverings or operating the heater where impurities in the air (such as tobacco smoke, candle smoke
etc.) exist, may cause the walls to become discoloured.
• WARNING:
The manufacturer of this appliance considers all surfaces as working surfaces with the exception of the control knob
and ash pan door. Where young children, pets, the elderly or infirm are concerned, a suitable fireguard should be used.
• Consult ALL instructions before installation and use of this appliance.
• This appliance is free from any asbestos material.
• Refractories and fuel bed are constructed from ceramic fibre.
• Slide control models : These appliances feature a battery-operated control system, and under normal usage will need a new battery
approximately every twelve months.
Burner/spark generator requirements - 1 x ‘PP3’ type (9 volt)
Refer to the appropriate section of these instructions for details of how to change the battery.
• Remote control models : This appliance features a battery-operated remote control system, and under normal usage will need
new batteries approximately every twelve months.
Remote control Handset requirements - 1 x ‘PP3’ type (9 volt)
Receiver/motor unit requirements - 4 x ‘AA’ type (1.5 volt)
Refer to the appropriate section of these instructions for details of how to change the batteries.
I N S T A L L A T I O N I N S T R U C T I O N S
2
GB IE
•
Manufacturers' Instructions.
•
The Building Regulations issued by the Department for Communities and Local Government, the Building Standards (Scotland)
(Consolidation) Regulations issued by the Scottish Development Department.
•
Relevant British Standards insofar as the relevant areas are not covered by these instructions.
•
For Republic of Ireland, reference should be made to the current edition of IS813 (the relevant standards governing installation).
1.0 IMPORTANT NOTES
©
2011 Focal Point Fires plc.
Section
1.0
2.0
3.0
4.0
4.1
5.0
6.0
7.0
7.1
8.0
9.0
10.0
11.0
11.1
11.2
11.3
11.4
12.0
Contents
Important Notes
Appliance Data
Installation Requirements
Site Requirements
Debris Collection Space
Ventilation
Pre Fabricated Flue Boxes
Unpacking the Appliance
Component Checklist
Preparing the Appliance
Preparing the Opening
Gas Supply Routing
Fitting the Firebox
Installation by Cable Fixing Kit
Gas Connection
Fuel Bed Layout
Fitting the Firefront / Frame
Testing and Commissioning
Page No.
2
3
3
3
4
5
5
5
5
6
7
7
7
8
8
8
8
8
Section
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
13.0
13.1
13.2
13.3
13.4
13.5
13.6
13.7
14.0
Contents
Operating the Fire (Manual control)
Operating the Fire (Slide control)
Operating the Fire (Remote control)
Spark Gap
Operating Pressure (Manual models)
Operating pressure (Slide & Remote models)
Flue Spillage Monitoring System
Testing for Spillage
Briefing the customer
Servicing
Cleaning the Ceramics
Removing the Burner
Servicing the Burner
Pilot Assembly
Removing the Firebox
Replacing the Batteries
(Slide control versions)
Replacing the Batteries
(Remote control versions)
Troubleshooting Guide
Page No.
9
9
9
10
10
10
10
10
11
11
11
12
12
12
12
12
12
13