superior fires Belrose Radiant Edwardian F500395 Installation & User'S Instructions Download Page 1 | Manualshive

Page: 1 / 20

superior fires Belrose Radiant Edwardian F500395 Installation & User'S Instructions Download Page 1

INSTALLATION & USER INSTRUCTIONS

Please note : All colour/finish variants are not shown.

All instructions must be handed to the user for

safekeeping.

MODELS COVERED BY THESE INSTRUCTIONS

FULL DEPTH RADIANT/CONVECTOR INSET GAS FIRE

Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not per-
mitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.

1

Revision A - 10/11

©

2011 Focal Point Fires plc.

GB IE

BS7977-1 : 2009

BS EN 509 : 2000

KM579168

WHATLEY RADIANT ELEGANCE BRASS NG

F500391

WHATLEY RADIANT GROVE BRASS NG

F500392

WHATLEY RADIANT GROVE BLACK FRAME NG

F500393

WHATLEY RADIANT GROVE CHROME NG

F500394

BELROSE RADIANT EDWARDIAN BLACK NG

F500395

BELROSE RADIANT EDWARDIAN CHROME NG

F500396

BELROSE RADIANT SOHO CHROME NG

F500397

BELROSE RADIANT VICTORIAN BLACK NG

F500398

BELROSE RADIANT VICTORIAN CHROME NG

F500399

CASONA RADIANT COAL NG

F500400

CASONA RADIANT PEBBLE REMOTE NG

F500401

WALTHER CONVECTOR ELYSEE BRASS NG

F500402

WALTHER CONVECTOR GROVE BRASS NG

F500403

WALTHER CONVECTOR GROVE CHROME NG

F500404

MALLORY CONVECTOR EDWARDIAN CHROME NG

F500405

MALLORY CONVECTOR VICTORIAN CHROME NG

F500406

Superior Fires

Christchurch, Dorset BH23 2BT

Tel: 01202 588 632
Fax: 01202 499326

www.superiorfires.co.uk

e : [email protected]

BELROSE RADIANT EDWARDIAN

MALLORY CONVECTOR VICTORIAN

CASONA RADIANT PEBBLE

WHATLEY RADIANT GROVE

MALLORY CONVECTOR EDWARDIAN

CASONA RADIANT COAL

WHATLEY RADIANT ELEGANCE

WALTHER CONVECTOR GROVE

BELROSE RADIANT VICTORIAN

WHATLEY RADIANT GROVE

WALTHER CONVECTOR ELYSEE

BELROSE RADIANT SOHO

1
2
3
...
»

Summary of Contents for Belrose Radiant Edwardian F500395





















Reviews:

No comments