background image

SuperiorFireplaces.us.com

127020-01_E

14

OPERATION AND MAINTENANCE GUIDELINES  

Continued

LOCATING ACCESS COVER PLATE

Sheet metal cover plates located underneath front hearth refractory may 

have shifted or moved out of place while fireplace was in transit. These 

cover plates must be kept in the proper location prior to using the fireplace 

(See Figure 23). 
For further operating guidelines, instructions and warranty infor-

mation, please refer to your homeowner's guide or contact your 

authorized dealer.

Figure 23 - Locating Access Cover Plate

Access Panel

REPLACEMENT PARTS

See Pages 16 to 18 for a complete replacement parts list. Use only 

parts supplied from the manufacturer.
Normally, all parts should be ordered through your IHP distributor 

or dealer. Parts will be shipped at prevailing prices at time of order.
When ordering repair parts, always give the following information:
1. The model number of the fireplace.

2. The serial number of the fireplace.

3. The part number.

4. The description of the part.

5. The quantity required.

6. The installation date of the fireplace.
If you encounter any problems or have any questions concerning the 

installation or application of this fireplace, please contact your dealer.

IHP

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

Visit us at SuperiorFireplaces.us.com

TECHNICAL SERVICE

You may have further questions about installation, operation, or 

troubleshooting. Please contact your IHP dealer for any questions 

or concerns. When contacting your dealer please have your model 

and serial numbers of your fireplace ready. You can also visit our web 

site at SuperiorFireplaces.us.com.

Summary of Contents for WRE3036WH

























Reviews: