15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installation Instructions
900358-00, 01/2018
Innovative Hearth Products
DRT63STTYN Power-Vent Direct-Vent Fireplaces
Proper Sizing of Gas Line
Properly size and route the gas supply line
from the supply regulator to the area where the
appliance is to be installed per requirements
outlined in the National Fuel Gas Code, NFPA
54 - latest edition (USA) or CAN/CGA-B149.1
- latest edition (Canada).
IMPORTANT: It is critical that a licensed
installer perform this step strictly per
NFPA.
Never use galvanized or plastic pipe. Refer
to
Table 6
for proper sizing of the gas sup-
ply line, if black iron pipe is being used. Gas
lines must be routed, constructed and made
of materials that are in strict accordance with
local codes and regulations. We recommend
that a qualified individual such as a plumber or
gas fitter be hired to correctly size and route
the gas supply line to the appliance. Installing
a gas supply line from the fuel supply to the
appliance involves numerous considerations of
materials, protection, sizing, locations, controls,
pressure, sediment, and more. Certainly no one
unfamiliar and unqualified should attempt sizing
or installing gas piping.
NOTE:
• All appliances are factory-equipped with
a flexible gas line connector and 1/2 inch
shutoff valve (see
Figure 35
on
Page 25
)
.
• See
Massachusetts Requirements
on
Page
6
for additional requirements for installations
in the state of Massachusetts in the USA.
• The gas supply line should not be connected
to the appliance until
Step 6
(
Page 25
)
.
• A pipe joint compound rated for gas should be
used on the threaded joints.
Ensure propane
resistant compounds are used in propane
applications
. Be very careful that the pipe
compound does not get inside the pipe.
• It is recommended to install a sediment trap
in the supply line as close as possible to
the appliance (see
Figure 35
on
Page 25
)
.
Appliances using Propane should have a
sediment trap at the base of the tank.
• Check with local building official for local
code requirements (i.e. are below grade
penetrations of the gas line allowed?, etc).
Schedule 40, Black Iron Pipe
Inside Diameter (Inches)
Schedule 40 Pipe
Length (feet)
Natural
Gas
Propane
Gas
0-10
1/2
3/8
10-40
1/2
1/2
40-100
1/2
1/2
100-150
3/4
1/2
150-200
3/4
1/2
Table 6
Figure 14 - INDOOR / OUTDOOR
Right Side Front Corner
(Valve Side) of Fireplace Framing
19-1/2"
(495 mm)
7”
(178 mm)
1-1/2”
(38 mm)
Figure 13 - INDOOR / INDOOR
7”
(178 mm)
Right Side Front Corner
(Valve Side) of Fireplace Framing
19-1/2"
(495 mm)
Right Side Front
Corner Of Fire-
place Framing
Step 2. ROUTE GAS LINE
NOTICE: For indoor/outdoor installations,
the CONTROL SIDE of the fireplace must
be installed on the INDOOR side.
Route a 1/2" (13 mm) gas line along the inside
of the right side framing as shown in
Figures 13
and 14
. Gas lines must be routed, constructed
and made of materials that are in strict accor-
dance with local codes and regulations.
All appliances are factory-equipped with a
flexible gas line connector and 1/2 inch shutoff
valve
(see Step 6 on Page 25).
The incoming gas line should be piped into the
valve compartment and connected in one of the
two methods as shown in
Figure 35
on
Page 25
.
Step 3. INSTALL VENT SYSTEM
General Information
These instructions should be used as a guide-
line and do not supersede local codes in any
way. Install venting according to local codes,
these instructions, the current National Fuel
Gas Code (ANSI-Z223.1) in the USA or the
current standards of CAN/CGA-B149.1 and
-B149.2 in Canada.
These fireplaces are designed, tested and
listed for operation and installation with,
and only with, Secure Vent
®
(SV4.5) Direct-
Vent System Components, manufactured by
Security Chimneys International. These ap-
proved vent system components are labeled
for identification. DO NOT use any other
manufacturer's vent components with these
appliances.
Ensure clearances are in accordance with
local installation codes and the requirements
of the gas supplier.
Dégagement conforme aux codes d’installa-
tion locaux et aux exigences du foumis-
seunde gaz.
Use only approved venting components. See
Approved Vent Components
on
Page 4
.
These fireplaces must be vented directly
to the outside.
The vent system may not service multiple
appliances, and must never be connected to a
flue serving a solid fuel burning appliance. The
vent pipe is tested to be run inside an enclosed
wall (such as a chase). There is no requirement
for inspection openings in the enclosing wall at
any of the joints in the vent pipe.
Venting System
With the appliance secured in framing, de-
termine vent routing and identify the exterior
termination location. The following sections
describe horizontal (exterior wall) vent applica-
tions.
A list of approved venting components
is shown on
Page 34
.
IMPORTANT NOTE REGARDING
PROPANE INSTALLATIONS
Using a propane tank smaller than
100 lbs may create pressure loss and
insufficient fuel delivery, which can
cause sooting, severe delayed ignition,
or other malfunctions (ref. NPFA 58).
Any damage as a result of insufficient
tank size or other improper installation is
NOT covered under the limited warranty.