background image

15

Frequently Asked Questions

FAQs

Question:

 Can I adjust power levels when cruise control is on?

Answer:

 No, only when cruise control is off. 

NOTE:

 Cruise control can be used as normal, you just can’t 

change power levels when cruise control is on.

Question:

 Should I remove the Pulsar LT prior to going to the 

dealer?

Answer:

 Yes, please remove the Pulsar LT as to eliminate it from 

the system so they can perform any updates or services.

Question:

 How do I check what level I am on when cruise control 

is off?

Answer:

 Simply press Cancel on power steering keypad.

Question:

 Can I “stack” or use other tuners with this device?

Answer:

 No, please do not use any other tuners when the Pulsar 

LT is in use or installed. Stacking tuners with the Pulsar LT may 

cause serious damage to the vehicle.

Question:

 What is the best way to accurately measure tire size?

Answer:

 Mark a line on the ground where the center of the tire 

rests, then drive the vehicle for two full rotations of the tire and 

mark the spot where it comes to a rest with another line. Measure 

the length between the two lines and divide by two. Then divide 

that number by Pi π (3.14159265359).

Summary of Contents for L84 Pulsar LT

















Reviews: