manualshive.com logo in svg

Superchips L84 Pulsar LT, User Manual, Page: 13 / 16

Share
Download
Superchips L84 Pulsar LT User Manual Download Page 13

13

Clear DTC’s

STEP 1

 - Access the programming menu.

STEP 2

 - Using +RES or -SET, select mode 50 (MPH)

STEP 3

 - Press cancel cruise to select.

STEP 4

 - The speedometer will sweep to 140 MPH, indicating the function is 

complete.

STEP 6

 - The speedometer will sweep to 140 MPH, indicating the function is 

complete.

Axle Ratio Cont’d

DFM (Dynamic Fuel Management) Disable

STEP 1

 - Access the programming menu.

STEP 2

 - Using +RES or -SET, select mode 70 (MPH)

STEP 3

 - 3. 

Use the +RES or –SET wheel to adjust to the desired value.

 

a.0 = DFM  is active

 

b.10 = DFM is disabled

STEP 4

 - Press the cancel cruise control button to save the input value.

STEP 5 

- The speedometer will sweep 0 to 140 MPH indicating the function is 

complete.

Disabling DFM will automatically disable Auto Start/Stop

Auto Start/Stop Disable

STEP 1

 - Access the Programming Menu.

STEP 2

 - Using +RES or -SET, select mode 60 (MPH)

STEP 3

 - Use the +RES or –SET wheel to adjust to the desired value.

 

a. 0 = Auto Start/Stop is active

 

b. 10 = Auto Start/Stop is disabled

STEP 4

 - Press the cancel cruise control button to save the input value.

STEP 5

 -The speedometer will sweep 0 to 140 MPH indicating the function is 

complete.

Summary of Contents for L84 Pulsar LT

















Reviews:

No comments