manualshive.com logo in svg

Superabrasive Lavina 20, Owner'S Manual

Share
Download
Superabrasive Lavina 20 Owner'S Manual Download Page 12

Superabrasive 

Owner’s Manual - Lavina 20

®

  

09/2009 

 

Refers to Lavina 20

®

 Lavina 20

®

E 

 

12

Adjusting and Mounting Tools

 

Mount the tools only after ensuring that there is enough diamond bond material left. Be sure that the 
plates are always clean before mounting. Always use the special key for mounting or adjusting, as seen 
below Adjusting and mounting are shown on Fig.11. 
  

 

Figure 11 

 

Description of the Control Board 
 
1 Digital RPM indicator: 

indicates the revolution per minute of the grinding plates (not the revolution per 

minute of the entire unit). 

2 Potentiometer:  

 

changes the RPM of the grinding plates. 

3 Inverter alarm led:    

lights when the inverter goes into Alarm Mode. 

4 Reset button:  

 

resets the alarm of the inverter 

5 Forward/Reverse switch:  

chooses forward for clockwise rotation of the grinding plates or reverse for 
anti-clockwise rotation of the grinding plates. (could be used to open up 
diamond bond). By use of PCD plates check rotation direction! 

6 ON button:    

 

starts the motor 

7 Power led:    

 

lights when the power is on 

8 OFF button:    

 

stops the motor 

9 Emergency Switch:   

used in Emergency situations to put off the power completely 

 

Figure 12 

Summary of Contents for Lavina 20
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands