Superabrasive Owner’s Manual orginal language –
Lavina 20®N Pro/20®NHV Pro
2/2012
5
•
For not-suitable materials.
•
In
environments
which:
•
Possess risks of explosion
•
Possess high concentration of powders or oil substances in
the air
•
Possess risks of fire
•
Feature inclement conditions.
•
Possess electromagnetic radiation.
PREPARATION FOR
WORK
Make sure that:
•
You have closed the work area, so that no person
unfamiliar with operating the machine can enter the area
•
The tool plate and tools are adjusted to the machine
properly
•
There are no missing parts of the machine
•
The machine is in upright working position
•
The protection devices are working properly.
•
The electrical cable is free to move and follow the machine
easily. In order to keep the electrical cable from being
damaged, no vehicle should cross the zone where electrical
cables are situated.
PROTECTION DEVICES
•
The machine is equipped with several protection devices
including the following:
•
An emergency stop button
•
A protection skirt and a hood for protecting the tool plates.
•
These devices protect the operator and/or others persons
from potential injuries. Do not remove them. On contrary,
before using the machine, please ensure that all protection
devices are mounted and function properly.
ARREST FUNCTIONS
Functions of arresting of the machine are following:
•
Button to stop the motor (category 1)
•
Emergency button (category 1)
SAFE USE
•
The Lavina 20N/20NHV Pro is designed to eliminate all
risks correlated with its use. However, it is not possible to
eliminate the risks of an eventual accident with the
machine. Unskilled or uninstructed operator may cause
correlated residual risks. Such risks are:
•
Position Risks due to operator’s incorrect working
position
•
Tangling up Risks
due
to
wearing
inappropriate working clothes
•
Training Risks due to lack of operational training
NOTE
: In order to reduce all consequences of the above-
mentioned risks, we advise that machine operators will follow
the instructions in the manual at all times.
RESIDUAL RISKS
•
During the normal operating and maintenance cycles, the
operator is exposed to few residual risks, which cannot be
eliminated due to the nature of the operations.
BEFORE YOU BEGIN
•
Working area must be clear from any debris or objects.
•
A first-time operator must always read the manual and pay
attention to all safety instructions.
•
All electric connections and cables must be inspected for
potential damages.
•
Ground wire system of the power supply must be also
inspected.
•
Perform general daily inspections of the machine and
inspect the machine before each use.
•
Always inspect the safety devices:
•
The emergency break must be clear and working
•
The tool protector must be working
•
The machine must be clean
•
Never operate the machine in the rain!
•
Confirm that there are no missing parts especially after
transportation, repair or maintenance.
•
Before filling the water tank with water make sure the
machine is not working and the main switch is turned off.
•
Before turning on the machine make sure that the base is
placed on the floor, the machine MUST NOT be in an
upright position when turned on!
OPERATING MACHINE
•
When operating the Lavina 20N Pro/20NHV Pro, make
certain that there is no one, but you around the machine.
•
Never leave the machine unattended while working.
•
The electrical cable must move freely and must be damage-
free.
•
The water hose must move freely and must be damage-free.
•
Check if the floor, you work on, is not too uneven. If this is
the case, it may damage the machine.
AFTER WORK IS COMPLETED
•
Clean the machine and its surroundings properly
•
Empty and clean the water tank
•
Unplug the machine and wind up the electrical cable
•
Store the machine in a safe place
THE WORK AREA
•
Make certain that people or vehicles do not enter the work
area.
•
Avoid cables and hoses being in the way.
•
Always check the floor for debris
PERSONAL PROTECTIVE EQUIPMENT (PPE)
•
Always wear safety shoes when working with the machine.
•
Always wear ear protectors when working with the machine.
•
All personnel in the immediate work area must wear safety
glasses with side shields.
•
Always wear safety gloves when changing the tools.
•
Always wear clothes suitable for the work environment.
OPERATOR
•
The Lavina 20N Pro/20NHV Pro machine.
•
The operator must know the machine’s work environment.
•
Only one operator at a time can work with the machine.
•
The operator must be properly trained and well instructed
prior operating the machine.
•
The operator must understand all the instructions in this
manual.
•
The operator must understand and interpret all the drawings
and designs in manual.
•
The operator must know all sanitation and safety regulations
pertaining to the operation of
•
The operator must have floor grinding experience.
•
The operator must know what to do in case of emergency.
•
The operator must have an adequate technical knowledge
and preparation.
