background image

Updated: 10 October, 2009

Page 8

REF: REI-90-0611

B1. Press

SET

until the left display shows

P1-1

, the right display shows “Temperature in degree

celcius ” of the 1

st

set upper mould, press “

” or “

” to set up the new temperature.

B2. Press

SET

until the left display shows

P1-2

, the right display shows “Temperature degree ” of

the 2nd set of upper mould, (this only exists if the have two sets of moulds) push “

” or “

to set up the new temperature.

B3. Press

SET

until the left display shows

P1-3

, the right display shows “Temperature degree” of

the printer heater, push “

” or “

” to set up the new temperature.

C. Press “SET” until, the left display shows

P2

, this represents the counter calculation mode, the

right display shows the counting mode, “LOC” means the counter reset is locked, it will

continuously count from the last figure. If “OPN” is selected, it means the counter reset to zero.

The factory setting is

OPN

.

D. Press the “SET” key until the left display will show

P3

, and the right display shows sealing

time, use “

”, “

” keys to increase or decrease the value by one unit (0.1 second). Generally,

the value is assigned between 010 and 020. It is set at 015 at the factory.

E. Press the “SET” key until the left display will show

P4

, and right display shows the cup waiting

time, this indicates the cup will wait for before moving into the sealing position. Use “

”, “

keys to increase or decrease the value by one unit (0.1 second). Generally, the value is assigned

between 005 and 015. It is set at 010 (1 sec) at the factory. (This function based on the whether

sealing film is printed or non- printed, and with or without a date printer)

F. Setting the film-length for sealing and date printing:

(1) Printed film without date printer

Press the

SET

key until the left display shows

P5

, and set the right display value to”000”.

This indicates that the film will be controlled by an eye-mark sensor.

(2) Printed film with date printer, printing once in a cycle.

Press the

SET

key until the left display shows

P5

, and set the right display value to

000

,

indicating the film is controlled by the an eye-mark sensor, press the “set” key to

P8

and

choose printer type, the date printer will print the film at the same time when sealing.

(3) Printed film and date printer, printing twice in a cycle:

Press the

SET

key until the left display shows

P5

, and set the right value to

000

, Press

the set key again till

P7

; the right display will give a value between “001~199”, set the

correct value for the distance between the 1st printing and 2nd printing, press the “set” key

to

P8

and choose printer type, (The 1st printing is operated with the sealing mould

simultaneously).

(4) Non-printed film and without date printer

Press the

SET

key until, the left display shows

P5

, and set the right value to

003

. This

indicates the film will be controlled by length counter, press the “set” key until, the left

Summary of Contents for REI-90F


















Reviews: