manualshive.com logo in svg

SunStar KM-1957-7, User Manual

Share
Download
SunStar KM-1957-7 User Manual Download Page 20

20

4-11. Adjusting Parameter of Sub Thread Adjusting Device 

- The default value of A-95 is “0”.

Parameter No.

Set Value

Function Name

A-95

0

1

Use the main thread adjusting device

①

. In order to run the sub thread adjusting device

②

while

using the main device, press the sub thread tension switch. Then with the lamp turned on, the dish

for the sub thread adjusting device

②

is closed.  

After trimming, the sub thread tension switch is automatically turned off. 

In the case where A-95’s parameter is set at “1”, the lamp of the sub thread tension switch is on,

and the sub thread adjusting device 

②

is running like the main thread adjusting device

①

.

In this case, even after trimming, the sub thread tension switch is not automatically turned off.  

In order to release the tension of the sub thread adjusting device

②

, press the sub thread tension

switch to turn it off. 

4-12. How to Use Dual Tension

1. Main Thread Adjusting Device

- Adjust tension of the main thread adjusting device

①

in line with the main sewing material conditions.  

- Adjust the main thread adjusting device

①

and the tension of the lower thread in order to create loops at the center of the

sewing material at even stitch length.  

2. Sub Thread Adjusting Device

- Sub thread tension control assembly

②

is a device that users increase easily the upper thread tension depending on the materials

or the change of stepped pulley while stitching.  

- The sub thread adjusting device

②

should be adjusted in line with the tension of the main thread adjusting device

①

and the

conditions of sewing materials with height difference. 

3. Operating Main

·

Sub Thread Adjusting Devices

- The main

·

sub thread adjusting devices

①

, 

②

are run by pneumatic pressure. In particular, the sub thread adjusting device

②

can be turned on and off easily with functional switches.  

- If you press sub thread tension control button while stitching the lamp is turned on and the upper thread tension increases at the

same time. If you press the button again, the lamp is turned off and the upper thread tension decreases at the same time.

[ Figure 22 ]

Thread adjusting device for 1 needle

Thread adjusting device for 2 needles

①

②

①

②

Summary of Contents for KM-1957-7












































Reviews:

No comments

Brands by name

Popular brands

Load more brands