Sunrise Medical QUICKIE S-11 Service Manual Download Page 21 | Manualshive

Page: 21 / 24

background image

QUICKIE S-11 SERVICE MANUAL

PAGE 15

2005

SUNRISE MEDICAL

Disassembly/Reassembly, and Adjustment (cont)

A4.14

A4.15

Step 6 - Battery

Disassembly
a. There are two ways to access the batteries. One is fold
the back and fl ip the seat forward by release the rear seat
post latches (fi gure A4.13).

b. The other is to remove the quick release pins on the bot-
tom frame (fi gure A4.14) and removes the top main frame
and seat (fi gure A4.15).

c. Remove the Velcro strap (fi gure A4.16).
d. Depress the locking tabs and unplug the battery connec-
tors.
e. Grip the battery handle and pull the battery out
base.
Reassembly
a. Perform the reverse of instructions above.

A4.13

A4.16

«
...
19
20
21
22
23
...
»

Summary of Contents for QUICKIE S-11

























Reviews:

No comments

Related manuals for QUICKIE S-11

Brand: Cando Pages: 2

Brand: Bischoff & Bischoff Pages: 73

Brand: Invacare Pages: 108

Drop Mount Hardware

Brand: SPEX Pages: 20

Adventure Control

Brand: Carpe Iter Pages: 10

Brand: bp Pages: 31

Brand: Pride Pages: 36

Brand: Pride Pages: 44

Jazzy 600 Series

Brand: Pride Pages: 55

Tennis Wheelchair

Brand: Roma Sport Pages: 4

Brand: Roma Medical Pages: 16

multichair 4000

Brand: Nuprodx Pages: 9

Brand: Spencer Pages: 22

Brand: Glide Pages: 13

Brand: Vermeiren Pages: 136

ROHO Nexus SPIRIT NS1414C

Brand: Permobil Pages: 72

Brand: Karma Pages: 44

Brand: Xsensor Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands