background image

QUICKIE S-11 SERVICE MANUAL

PAGE  11

2005

SUNRISE MEDICAL

Section 4

Disassembly/Reassembly, and Adjustment

Disassembly
a. Squeeze down the locking legs of the 3 pin charger plug
and unplug it from the rear of the chair. (figure A4.1).
b. Rock the controller plug back and forth until it is loose
and then unplug it.

Note: Remember to lay cables on the seat otherwise they
may become tangled when taking off the seat.

c. Remove the Front Seat Post Knobs (figure A4.3).
d. Lift up the rear seat post latching levers and push the 
seat forward. (figure A4.2).  
e. Remove the front seat post knobs and slide the seat 
backward and lift it off of the base.

Reassembly
a. Line up the front seat frame with the front seat posts,
slide the seat forward to the stops and let the seat frame
rotate down in to the rear seat post latching brackets.
b. Make sure the latching levers are locked flat against the
seat post brackets.
c. Plug the controller plugs into the plug receptacles at the
rear of the chair.
d. Install the Front Seat Post Knobs (figure A4.3).

Step 1 - Controller and Seat

Note: When using the terms “Right Hand, Left Hand” this is referenced as if seated in the chair.

A4.1

A4..2

A4.3

Summary of Contents for QUICKIE S-11

























Reviews: