background image

B.  WEIGHT LIMIT

WARNING

1. The user plus items carried should never exceed the total

weight capacity identified on your chair.

2. Never use this chair for weight training. 
3. Exceeding the weight limit is likely to damage the seat,

frame, or fasteners, and may cause severe injury to you or
others from chair failure.

4. Exceeding the weight limit will void the warranty.

C. CONTROLLER SETTINGS

WARNING

Be aware that you may need to adjust the controller settings of
your chair.

1. Check and adjust the settings every six to twelve months.
2. Consult your supplier to adjust the control settings immedi-

ately if you notice any change in your ability to: 
• Control the joystick
• Hold your torso erect
• Avoid running into objects. 

D. SAFETY CHECK-LIST

WARNING

Before each use of this chair: 

1. Make sure the chair operates smoothly. Check for noise,

vibration, or a change in ease of use. (They may indicate low
tire pressure, loose fasteners, or damage to your chair). 
• Inspect any problem.  Your authorized dealer can help you

find and correct the problem. 

2. Make sure batteries are charged. Green lights on charge

indicator will light up when charge is full. Yellow lights indi-
cate battery charge level is getting low. Red lights indicate
batteries are in immediate need of charging.

E.  CHANGES & ADJUSTMENTS

WARNING

Never

use non-Quickie parts to replace Quickie provided parts or

make changes to your chair unless authorized by Sunrise. (Doing so
will void the warranty and may create a safety hazard.) 

F.  ACCESSORIES

WARNING

Accessories designed by manufacturers other than Sunrise, not avail-
able through Sunrise order process have not been tested or
approved for use by Sunrise.

1. If you modify or adjust this chair it may increase the risk of a

fall or tip-over. 

2. Modifications unauthorized by Sunrise constitutes remanu-

facturing of the wheelchair. This voids the warranty. The
user then assumes all future liability for the wheelchair.

WARNING

Heed all warnings in this section. If you fail to do so, a fall, tip-over
or loss of control may occur and cause severe injury to you or
others.

A. NOTICE TO USER AND ATTENDANTS

WARNING

User:

1. Before using this chair, you should be trained in its safe use

by your health care professional. 

2. Every wheelchair is different. Take the time to learn the feel

of this chair before you begin riding. 

3. Be aware that you must develop your own methods for the

safe use of this chair that are best suited to your level of
function and ability. 

4. Have someone help you practice bending, reaching and

transfers until you learn how to do them safely. 

5. Never try a new maneuver on your own unless you are sure

it is safe. 

6. Get to know the areas where you plan to use your chair.

Look for hazards and learn how to avoid them. 

7. Always wear a positioning strap.
8. Do not use a wheelchair if the joystick does not spring back

to the neutral position.

9. Do not use your wheelchair if the joystick boot is ripped or

damaged.

10. Do not try to tip this wheelchair without an attendant present.
11. Do not allow additional riders, the chair may become unstable.

User and Attendants:

1. When transferring the user in or out of the wheelchair

never use the footplate as a platform.

2. Do not lift this wheelchair by any parts that are removable,

doing so may result in damage to the wheelchair or injury to
the user.

3. Never try to stop or slow this wheelchair with the wheel

locks (if applicable). Wheel locks are designed to prevent
the chair from moving when stopped. They are not brakes.

4. Always keep your hands and body parts clear of moving

parts to help prevent injuries.

Attendants:

WARNING

Make sure you heed all warnings and follow all instructions in each
section of this manual. Warnings that apply to the user also apply
to you. 

1. Do not stand or sit on any portion of this wheelchair.
2. You need to work with the user, and the user’s doctor,

nurse or therapist, to develop safe methods best suited to
your abilities and those of the user. 

3. To manually push the chair you must release the motor locks. 

• Do not engage or disengage motor locks 

unless

power to

the chair is 

off

.

• Make sure you have full control over the chair when you

release the motor locks. When you do so the chair will not
have brakes. 

• Make sure the chair is on level ground before you release

the motor locks.

4. Propel this chair by the push handles only. They provide

secure points for you to hold the rear of the chair to pre-
vent a fall or tip-over. 

5. Check to make sure push handle grips will not rotate or slip off. 

VI. GENERAL WARNINGS

Q UI C KI E   PU LS E

7

119832 Rev. G

Summary of Contents for Pulse 5BC













































Reviews: