background image

119832Rev. G

20

Q UI C KI E   PU LS E

VIII. USE AND MAINTENANCE

Q. MOTOR LOCK 

Disengage the Motor Lock when you need to manually push the chair. (For example, in an
emergency, or if batteries fail).

WARNING

1. Do not disengage Motor Lock unless chair power is off.
2. With either one or both locks released, the chair will not operate and the battery

charge indicator will flash 9 bars rapidly (if power to the chair is on.)

3. Be aware that the chair will not have brakes in the free-wheel position.
4. Make sure that the person pushing the chair has full control when Motor Lock lever is

disengaged.

1.   Disengage the Motor Lock to push the chair manually

a. The Motor Lock lever (A) is attached to the rear section of the motors located

towards the back of the chair.

b. Push the Motor Lock lever down to disengage.

2.   Engage the Motor Lock to drive the chair

a. The Motor Lock (A) is attached to the upper rear section of the motors located at

the back of the chair.

b. Pull the lever up to engage the Motor Lock.

R.  BATTERY REMOVAL 

1.   To remove the batteries before transporting or servicing: 

a. Carefully flip back the seat (see Section XI T Seat removal)
b. Remove the shroud (see Section XI E Shroud removal) .
c. Unplug the main power connect (B)
d. Lift the batteries out of the frame using the battery strap as a lifting handle.

2.   Battery installation

See section X.  (Batteries) for installation

WARNING

Batteries may weigh up to 39 lbs.  Care must be taken to avoid injury when lifting up on bat-
tery straps.

S.  CAPTAINS SEAT 

The Captains seat back can be manually reclined, folded, or angle adjusted.

1.   Adjusting the recline angle

a. To adjust, pull up on the release lever(C) located on the right side of the backrest.
b. Reposition the backrest forward or backward to the desired position.
c. Release the lever (C) and wiggle the backrest to make sure it locks in place.

2.   Folding the Back (unoccupied)

a. To fold, Pull up on the release lever(C) located on the right side of the backrest.
b. The backrest should spring forward into the folded position as shown. 
c. Release the lever.
d. To unfold the back, pull up on the release lever (C) and adjust the back to an upright

position.

20

21

23

22

22

23

C

C

20

A

B

21

Summary of Contents for Pulse 5BC













































Reviews: