background image

 

13 

 

7.  Pulse  measurement 

–  After  holding  onto  the  handle  pulse  sensors  for  a  few  seconds,  the 

computer  will  show  your  current  heart  rate  in  beats  per  minute.  To  ensure  the  heart  rate 
readout  is  precise,  please  hold  the  handle  pulse  sensors  with  both  hands.  You  may  preset 
target pulse before training starts. Once your current heart rate is achieved, the computer will 
beep to notify you. 

8.  Recovery 

– When the PULSE is working, you can press the “RECOVERY” button to start the 

recovery  test  function.  The  computer  will  count  down  from  0:60  second  to  0:00  and  the 
heartbeat symbol will flash until the countdown reac

hes “0:00”. For the 60 second countdown 

period, please keep your hands on the handle pulse sensors

. The screen will display “F1 to F6” 

to show your recovery status. F1 is the best, and the F6 is the worst. You may keep exercising 
to improve your heart rate recovery status and check it by using the Recovery function. 

9.  Body Fat -   

9-1.  Press the BODY FAT key to enter body fat measurement. 
9-2.  Press  MODE &  SET buttons  to  input  your  personal  data.  The  personal data available  is 

described as the following: 

        AGE: 

10 ~ 99 years    HEIGHT: 100 ~ 250 cm (or 3

’03” ~ 8’02“)    WEIGHT: 10 ~ 200 kg   

(or 22 ~ 440 lb)   

9-3.  After all personal data has been entered, you can press the BODY FAT button and hold on 

handle pulse sensors to start the body fat testing. 

9-4.  It  takes  a  few  seconds  to  test  the  body  fat.  If  you  did  not  hold  onto  the  handle  pulse 

sensors during the test, the LCD will show the error sign 

‘Err’ after 10 seconds. 

9-5.  After  testing  is  finished,  you  will  see  a  percentage  and  BMI  figure  (Body  Mass  Index) 

display on the main LCD in sequence by scan mode. 
BODY FAT %: Calculated from your personal data to show the value from 5%~50%. 
BMI: Calculated from your personal data to shows the value from 1.0~99.99.

 

 

9-6.  Press any key to return to the main screen.

 

 

 
 

Note:

 

1.  If  training  has  stopped  for  4  minutes,  the  screen  will  show  room  temperature,  clock,  and 

calendar display automatically.   

2.  If the computer did not receive any speed signal or key input for one minute, the LED backlight 

will turn off automatically. Any speed signal input or key input can turn on the LED backlight 
automatically.   

3.  If the computer display is abnormal, please re-install the batteries and try again. 
4.  Battery Spec: 1.5V UM-3 or AA (2PCS). 

 

 

 

 

 

 

Summary of Contents for SF-B2956

















Reviews: