background image

 

 

BATTERY INSTALLATION & REPLACEMENT 

 

1

1a

1c

 

 

BATTERY INSTALLATION: 

 
1.  Take out 2 AA batteries from computer box. 
2.  Press  the  buckle  of  the  battery  cover  on  the  back  of  the 

Computer  (No.  1)

,  then  remove 

battery cover. 

3.  Install 2 AA batteries into the battery case on the back of the 

Computer (No. 1)

. Pay attention 

to the b and 

– ends before installing. 

4.  Press  the  buckle  of  the  battery  cover,  then  put  the  battery  cover  back  to  the  back  of  the 

Computer (No. 1).

 

 

The installation is complete! 

 

BATTERY REPLACEMENT: 
 

1. Press the buckle of the battery cover on the back of the 

Computer (No. 1)

, then remove the 

battery cover. 

2. Remove the 2 old AA batteries in the battery case and install 2 new AA batteries into the battery 

case on the back of the 

Computer (No. 1)

. Pay attention to the b and 

– ends before 

installing. 

3. Press  the  buckle  of  the  battery  cover,  then  put  the  battery  cover  back  to  the  back  of  the 

Computer (No. 1).

 

 

The replacement is complete! 

 

NOTE:

 Always change both batteries at the same time. Do not mix battery types and do not mix 

old and new batteries. Dispose of batteries according to your state and regional guidelines. 

 

Battery Cover 

Battery 

Summary of Contents for SF-B2956

















Reviews: