background image

Cautions: 

1. Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of pavilion construction. 
2. The area for assembly should not be less than 6 feet from any obstruction such as fence,
garage, house, over hanging branches, laundry line or electrical wires. 
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for safe
assembly. 
4. Some parts may contain sharp edges. Wear protective gloves if necessary during assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all 
instructions before assembly and use. 
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the pavilion in
the ground. If you wish to secure the pavilion to a wood deck or concrete surface, you will need 
to purchase fasteners appropriate for these surfaces. These are readily available at your local 
hardware store or home center. 
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for, or otherwise regulate, installation and use. 
9. While this pavilion is manufactured to withstand gale force winds utilizing only the supplied
ground stakes, in areas subject to frequent severe weather, securing the pavilion to a deck, 
concrete patio or footings should be considered. 
10. Your pavilion has been engineered to accommodate winter snow loads incurred in most
areas. Removal of accumulated snow on the pavilion roof with a roof rake is recommended. In 
areas that are regularly subject to blizzard conditions however, removal of the roof panel is 
suggested. The assembled roof structure can simply be left intact until warmer conditions 
return.

 

Assembly Instructions:

 

Our clear, easy-to-follow, step-by-step instructions will guide you through the project from start 
to finish. The final product will be a quality piece that will go together smoothly and give years 
of enjoyment. 
All you need a screwdriver and hammer, two ladders (not included) whose height is no less 
than 2.5m. 
Parts identification: For ease of identification, all parts are labeled to correspond to the Step 
number in which the part is used. 

Summary of Contents for L-GZ605PST-A4













Reviews: