Sungrow SG60KTL User Manual Download Page 32

Page: 32 / 100

5 Mechanical Installation

User Manual



Take enough space for convection into consideration when installing multiple

inverters. It is suggest to stagers the inverters.



Do not install the inverter in a confined space.

Inverter will not work normally if otherwise.



Install the inverter where children cannot reach.



Do not install the inverter near residential area.

Noise can be produced during inverter operation

which may affect the daily life.

5.2

Moving Inverter to Installation Site

To install the inverter, remove the inverter from the packaging and move it to the
installation site. Follow the instructions below during inverter moving:



Always keep in mind the weight of the inverter.



Lift the inverter by gasping the handles on two sides of the inverter.

Summary of Contents for SG60KTL





































































































Search results

Summary of Contents for SG60KTL

Reviews:

Related manuals for SG60KTL

Brands by name

Popular brands

Sungrow SG60KTL, User Manual

Search results

Summary of Contents for SG60KTL

Reviews:

Related manuals for SG60KTL

Brands by name

Popular brands