background image

5001A and 5002A: 

Parts Breakdown and Operating Manual 

2  

rev . 3/13/17

WARNING

RPM

RPM

RPM

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.

It is the responsibility of the owner to make sure all personnel read 
this manual prior to using the device. It is also the responsibility of 
the device owner to keep this manual intact and in a convenient  
location for all to see and read. If the manual or product labels are 
lost or not legible, contact Sunex for replacements. If the operator is 
not fluent in English, the product and safety instructions shall be read 
and discussed with the operator in the operator's native language by 
the purchaser/owner or his designee, making sure that the operator 
comprehends its contents.
 

ELECTRICAL  WARNINGS

 

1.  This unit must always be used in accordance with all electrical   
 

and safety codes and ordinances including National Electric Code  

 

(NEC) and Occupational Safety and Health Act (OSHA). 

2.  Read, study, understand and follow all instructions before using. 
3.  Failure to follow all instructions listed below may result in electric  
 

shock, fire, explosion and/or serious personal injury. 

4.  Keep bystanders, children and visitors away while operating unit.  
 

Distractions can cause you to loose control and endanger others.  

5.  Store unit or product out of reach of children and other untrained  
 

persons, which can become dangerous in the hands of untrained  

 users. 
6.  Keep cord away from heat, oil, sharp edges or moving parts. 
7.  Do not remove any labels. Replace any damaged labels. 
8.  Slipping, tripping and or falling while operating product can be   
 

a major cause of serious injury or death. Be aware of cord left on  

 

walking or work surface. 

9.  Never remove, bypass or modify the grounding prong on any  
 

electrical plug in any way. Do not use any adapter plugs. Check  

 

with a qualified electrician if you are in doubt as to whether the  

 

outlet is properly grounded. 

10. Never use cord for carrying, pulling or unplugging the unit or  
 product. 
11.  Never attempt to plug in or operate unit or product with defective  
 

or damaged wires, power cord or power cord plug. Have any  

  defective or damaged parts replaced immediately by an 

 

 

authorized repair center. 

12.  Do not use in or around water, damp conditions, on wet surfaces,  
 

wet hands or while standing in water. 

13.  Do not use unit or product around any flammable material or fuel. 
14.  Keep unit or product away from hot objects. 
15.  Ground Fault Circuit Interrupter (GFCI) protection is to be provided  
 

on the circuit(s) or outlet(s) to be used for the wet location portable  

  luminaries. Receptacles are available having built-in GFCI 

 

 

protection and are able to be used for this measure of safety. 

16.  If an extension cord is required:      
 

•  Use only “UL Listed” extension cords.  

 

•  If you are using the tool outdoors, use an extension cord rated  

 

  and marked “For Outdoor Use”. Use only an extension cord type  

    SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, 

 

 

  SJEW, SJEOW, SJEOOW,SJW, SJOW, SJOOW, SJTW, SJTOW, or  

 

  SJTOOW.  

 

•  The cord must be of the proper size and type to supply the  

 

  correct current to the light without overheating. Otherwise the  

 

  extension cord could melt and catch fire, or cause electrical  

 

  damage to the light. This light requires the use of an extension  

 

  cord of 0 to 12 amps capability (up to 50 feet) with wire size  

 

  rated at 16 AWG. Longer extension cords require larger size  

 

  wire (smaller AWG number). AWG = American Wire Gauge. 

17. Stay alert, watch what you are doing and use common sense  
 

when operating a product. Do not use product while tired or under  

 

the influence of drugs, alcohol or medication. A moment of in 

  attention while operating the product may result in serious  
 

personal injury. 

18. Dress properly. Do not wear loose clothing or jewelry. Contain   
 

long hair. Keep your hair, clothing and gloves away from moving  

 

parts. Loose clothes, jewelry or long hair can be caught in moving  

 parts. 
19. Avoid accidental starting. Be sure switch is in the locked 

 

 

or "off" position before plugging product into the units power  

  source. Carrying product with your finger on the switch or  
 

plugging into power source with the switch "on" invites accidents.  

20. Disconnect product from power source or place switch in the  
  locked or "off" position before making any adjustments, 

 

 

changing accessories, or storing the product. Such preventative  

 

safety measures reduce the risk of starting the product accidently. 

21.  Do not overreach. Keep proper footing and balance at all times.    
 

Proper footing and balance enable better control in unexpected  

 situations. 
22.  If damaged, have the unit or product serviced before using. Many  
 

accidents are caused by poorly maintained products. 

23. Do not use (or modify) this product for any other purpose than  
  that for which it was designed without consulting the 

 

 

manufacturer's authorized representative. 

24.  Use only accessories that are recommended by the manufacturer.  
 

Accessories that may be suitable for one product may create a  

 

risk of injury when used on another product. 

25. This product may contain one or more chemicals known to the   
 

State of California to cause cancer and birth defects or other  

 

reproductive harm. 

Wash hands thoroughly after handling

26.  Handling the brass parts of this product will expose you to lead, a  
 

chemical known to the State of California to cause birth defects  

 

and other reproductive harm. 

Wash hands after handling

27. Failure to heed these warnings may result in serious or fatal 
 

personal injury and/or property damage.

ADDITIONAL GRINDER WARNINGS

 

1.  Always use guards and eye shields (users and bystanders).  
 

Always wear safety glasses or other eye protection and hearing  

 

protection when operating this tool and keep the eye shields  

 

mounted in their proper position on the wheel guard. 

2.  Always wear breathing apparatus when using this tool.
3.  Replace a cracked wheel immediately. Handle wheels carefully  
 

to avoid bumping or dropping. DO NOT use a grinding wheel that  

 

has been dropped. Before using, inspect each wheel for cracks or  

 

flaws and if these are evident, discard the wheel. 

4.  Before mounting a new wheel, be sure that it is marked with an  
 

RPM that is the same as, or higher than, the no load speed of the  

 

grinder as marked on the nameplate. 

5.  Never start a grinder with anyone, including the operator, standing  
 

in line with the wheel. After installing a re place ment wheel, stand  

 

to one side and allow it to revolve freely for about one minute. 

6. 

Do not grind on the sides of grinding wheels unless they are the  

 

special wheels designed specifically for this purpose. 

7.  Do not over tighten wheel nut. 
8.  Use only flanges furnished with this grinder. 
9.  Any damaged parts should be replaced with original parts and/or   
 

by a qualified service technician. 

10. 

Bolt Bench Grinder to a bench or pedestal to prevent 

 

 movements. 

11.  Use accessories only in the proper and intended manner. 
12. 

Spark Breakers should be installed perpendicular to the  

 

grinding wheel. If these are not installed properly, it is an  

 

OSHA violation. See picture on page 5.

Summary of Contents for 5001A
















Reviews: