background image

6808C 

rev. 04/11/19

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

             

 

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THESE STANDS, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING 
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using these stands. It is also the responsibility of 
the stand owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or 
not legible, contact Sunex for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to 
and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator 
comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical means, 
but only by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the 
use and operation of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its 
proper use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly secured loads, overloading, 
off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

  •  Read, study, understand and follow all instructions before using.
  •  This stand is designed to assist in stabilizing and supporting a vehicle that is raised by an in-ground or 
    above-ground lift. Do not use to support a vehicle.
  •  Inspect the stand before each use. Do not use if damaged, altered, modified, in poor condition, or has loose or missing hardware or   
    components. Take corrective action before using the stand.
  •  Do not use beyond rated capacity. Do not shock load.
  •  Use stands in pairs to stabilize the vehicle before starting repairs.
  •  Use only on a hard level surface. 
  •  Wear eye protection that meets ANSI Z 87.1 and OSHA standards.
  •  Adequately support the vehicle before starting repairs. 
  •  Center load on saddle. Do not use ends of saddle to support load.
 • 

Do not crawl under transmission or place any part of your body under transmission at any time.

  •  Be sure vehicle and stand are stable before performing any work.
  •   Failure to heed these warnings may result in fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, 
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS 
could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

MODEL 6808C

CAPACITY: 2 TON

UNDER HOIST SUPPORT STAND

WARNING: 

This product can expose you to chemicals including nickel, which is known to the State of California to 

cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Summary of Contents for 6808C














Reviews: