Sunell Security SN-TPC4201VT User Manual Download Page 52

Page: 52 / 59

Technical Specifications

Thermal Imaging Box Network Camera

User Manual

Issue V1.0 (2020-10-28

）

Type

Parameter

Description

accuracy

temperature, etc.

）

Multiple temperature area

Support.

Temperature response
time

Less than 30 millisecond

Effective range of working
temperature

-30

℃～

+60

℃

Temperature range

-20

℃～

+150

℃

Network
features

Network protocol

IPv4/IPv6, RTSP/RTP/RTCP,
TCP/UDP, HTTP, DHCP, DNS,
FTP, DDNS, PPPOE, SMTP, and
SIP

Heartbeat mechanism

Support

Stream mode

Unicast

Maximum user access
amount

Up to 10 users can access device
simultaneously.

ONVIF

Support

Automatic device discovery

Support

Interface
features

Network interface

RJ-45 and 10/100Base-T

Audio interface

1-channel audio input and 1-channel
audio output, supporting bidirectional
voice talkback.

Alarm interface

1-channel alarm input and 1-channel
alarm output.

Analog video output
interface

SMA

Pan & tilt control interface

1 RS 485, 1 RS 232

SD card connector

Micro SD card/HCSD card, 128 GB
to the maximum.

Reset

Support

Power interface

Support DC 12V

System
function

Intelligent alarm

Motion detection alarm, I/O alarm,
intelligent analysis, and disk alarm.

Summary of Contents for SN-TPC4201VT




























































Search results

Summary of Contents for SN-TPC4201VT

Reviews:

Sunell Security SN-TPC4201VT, User Manual, Page: 52 / 59

Search results

Summary of Contents for SN-TPC4201VT

Reviews: