Sun Microsystems StorageTek L40 Installation Manual Download

Page: 62 / 92

Standard Installation Procedure

1-28

Revision L

96053

3. Slide the drive tray assembly into the desired slot.

CAUTION:

Possible component damage:

Do not use a screwdriver to tighten the drive tray latch

knob.

4. Turn the knob all the way to the right to engage the latch and clamp it firmly into the frame.

5. Pull back on the tray to make sure the tray is securely latched. It should not move.

6. Connect the drive SCSI connector, P903, to the drive.

7. Connect the drive power cable, P904A/B, to the library.

8. Connect the serial interface connector, P6A/B, to the library.

1. P903
2. P904A/B
3. P6A/B

CAUTION:

Possible equipment damage:

Make sure the SCSI cable does not block the fan before

you close the drive door.

Possible cable damage:

Make sure you move the SCSI cable out of the way before

you close the drive door.

Possible component damage:

Do not use a screwdriver to tighten the drive door

latch knob.

9. Close the drive door and secure it by turning the drive door latch knob to your right.

10. Refer to your user’s guide to configure the drives.

Summary of Contents for StorageTek L40





























































































Search results

Summary of Contents for StorageTek L40

Reviews:

Related manuals for StorageTek L40

Brands by name

Popular brands

Sun Microsystems StorageTek L40, Installation Manual

Search results

Summary of Contents for StorageTek L40

Reviews:

Related manuals for StorageTek L40

Brands by name

Popular brands