Sun Microsystems StorageTek L40 Installation Manual Download | Manualshive

Page: 61 / 92

background image

96053

Revision L

1-27

Standard Installation Procedure

CAUTION:

Possible component damage:

Do not use a screwdriver for the drive door latch knob

or drive tray latch.

1. At the rear of the library, turn the drive door latch knob to your left to open the drive door.

1. Knob

CAUTION:

Load/unload problems:

The drive tray latch must be fully loosened (disengaged)

before you slide the tray into the slot. If the latch arm contacts part of the library
frame as it is being tightened, it cannot be rotated to its fully locked position, and the
tray will not be firmly locked into the drive slot. This can cause alignment problems
and the camera can have problems reading the target.

2. Holding the drive tray assembly as shown in the figure below, turn the drive tray latch knob all the

way to your right so that it is in its fully disengaged position.

1. Knob
2. Range
3. Latch arm (shown disengaged)

«
...
59
60
61
62
63
...
»

Summary of Contents for StorageTek L40





























































































Reviews:

No comments

Related manuals for StorageTek L40

Brand: U-Line Pages: 3

Brand: Y-E Data Pages: 48

Brand: ABSCO SHEDS Pages: 23

GEAR 175-9872-4

Brand: Yukon Pages: 7

StorageTek SL8500

Brand: Oracle Pages: 59

Brand: AA Products Pages: 2

TS-73AeU Series

Brand: QNAP Pages: 70

Brand: Western Digital Pages: 2

WDBAAP0000NBK - TV Live Media Player

Brand: Western Digital Pages: 2

VelociRaptor WD5000HHTZ

Brand: Western Digital Pages: 2

Brand: Western Digital Pages: 2

Brand: Western Digital Pages: 70

Brand: Western Digital Pages: 248

Brand: TerraMaster Pages: 13

Brand: Addonics Technologies Pages: 24

Brand: G-Technology Pages: 32

Brand: Neilsen Pages: 6

Brand: Supermicro Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands