manualshive.com logo in svg

Sun Microsystems 5220, Getting Started Manual

Share
Download
Sun Microsystems 5220 Getting Started Manual Download Page 9

ix

Preface

The

Sun StorageTek 5220 NAS Appliance Getting Started Guide

is a combined

installation, configuration, and getting started guide for the Sun StorageTek™ 5220
NAS Appliance. This guide describes how to install the appliance and its back-end
storage, how to connect the appliance and storage, and how to configure the system.

Product Documentation

In addition to this guide, the product includes the following documents. The
documents listed as online are available at

http://www.sun.com/hwdocs/Network_Storage_Solutions/nas

TABLE P-1

Product Documentation

Subject

Title

Part Number

Format

Location

Regulatory and
safety information
for the appliance

Sun StorageTek 5220 NAS Appliance Regulatory and Safety
Compliance Manual

819-7366-10

PDF

Online

Regulatory and
safety information
for the back-end
storage

Sun StorageTek 5220 NAS Array Regulatory and Safety
Compliance Manual

819-7367-10

PDF

Online

Installation poster

Sun StorageTek 5220 NAS Appliance Setup

819-7166-10

Print
PDF

Ship kit
Online

Recent information
not included in the
other documents

Sun StorageTek NAS OS Software Release Notes, Release 4.20

819-6652-nn PDF,

HTML

Online

Summary of Contents for 5220





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands