manualshive.com logo in svg

Sun Microsystems 5220, Getting Started Manual

Share
Download
Sun Microsystems 5220 Getting Started Manual Download Page 21

9

C H A P T E R

2

Installing the Appliance and
Back-End Storage

This chapter describes the process of installing the Sun StorageTek 5220 NAS
Appliance, a controller unit, and expansion units. It contains the following sections:

■

“Cabinets, Racks, and Rail Kits” on page 10

■

“Preparing for the Installation” on page 11

■

“Planning the Installation” on page 16

■

“Attaching the Universal Rail Kit” on page 19

■

“Installing a Unit in a Cabinet” on page 24

■

“Installing the Appliance in a Cabinet” on page 28

■

“Connecting the Power Cables” on page 42

■

“Next Steps” on page 42

The installation procedures in this chapter require the following items:

■

No. 2 Phillips screwdriver

■

No. 3 Phillips screwdriver

■

Antistatic protection

Caution –

Electrostatic discharge can damage sensitive components. Touching the

array or its components without using a proper ground might damage the
equipment. To avoid damage, use proper antistatic protection before handling any
components.

Summary of Contents for 5220





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands