background image

                                                                                    

56 

CHAPTER 8

 

ANNOUNCMENT OF PROBE SOUND WAVE 

OUTPUT 

 

  Mechanical Effect and Thermal Effect   

Research indicates that two different ultrasonic properties influence human body:one 

is when ultrasonic negative pressure exceeds some limited number,air pocket forms 

mechanical effect;another is when tissues absorb ultrasonic,appearance of heat energy 

of ultrasonic may cause thermal effect.two parameters which are mechanical index MI 

and thermal index TI can explain two types of effects influencing level,the smaller value 

of MI/TI is,the less bio effect produce. 

Attention:

 

1.  The nature of the transducers within the probes is such that degradation can 

occur over extended lengths of time.The sensitivity test can determine the sensitivity of 
probes,and should be performed before each use. 

2.    The results of the sensitivity tst can not meet the requirements ,indicating it may 

not be sensitive enough to perform accurate scans.Is general this is due to a loss of 
sensitivity in the probe .If this is the case the probe should be replaced . However,in 
order to confirm that it is the probe which is the case of the problem,it is necessary for 
evaluation by SunKingdom Company.

 

 

Tissues Exposed to Ultrasound Energy 

SK-3000A equipment can only be used in ophthalmology, with A-scan and B-scan 

probes. 

Warning: This device cannot be used for infants. 

 

Warning section (as low as possible): 

When used according to the recommended method, the energy will be weakened by the 

organization between the converter and the focus. The value shown here is the value at 

the focus. The intensity of focus is the highest. 

Summary of Contents for SK-3000A


































































Reviews: