background image

WARNING

!

You must fully read, understand and follow these warnings 

and instructions (written and video)! Failure to follow these 

instructions may cause serious injury or death!!

You 

MUST

 also view the enclosed DVD 

BEFORE

 using your new treestand!!

WEIGHT LIMIT

SINGLE USER

300 LBS. X 1 TOTAL*

DO NOT EXCEED THIS LIMIT!

(* Includes all gear) 

• 

IT IS IMPORTANT TO NOTE THAT A FALL CAN OCCUR AT ANY 

TIME AFTER LEAVING THE GROUND.

• 

ALWAYS MAINTAIN THREE POINTS OF CONTACT WHEN YOU 

CLIMB THE LADDER SECTION OF THIS TRIPOD!

• 

READ AND UNDERSTAND ALL OF THE MANUFACTURER’S 

WARNINGS AND INSTRUCTIONS AND USE ALL SAFETY DEVICES 

PROVIDED.  CONTACT SUMMIT TREESTANDS FOR ANY 

QUESTIONS.  FAILURE TO DO SO COULD RESULT IN INJURY OR 

DEATH!

• 

A SIGNAL DEVICE SUCH A MOBILE PHONE, RADIO, WHISTLE, SIGNAL FLARE OR PERSONAL LOCATOR DEVICE (PLD) MUST BE ON YOUR 

PERSON AND READILY AVAILABLE AT ALL TIMES!  ALWAYS INFORM SOMEONE OF YOUR HUNTING LOCATION, WHERE THE TRIPOD WILL 

BE LOCATED AND THE EXPECTED DURATION OF THE HUNT!

• 

DO NOT USE THIS TRIPOD UNLESS YOU ARE IN GOOD PHYSICAL SHAPE AND HAVE NO PHYSICAL LIMITATIONS OR MEDICAL CONDITIONS 

WHICH MAY PREVENT YOU FROM SAFELY USING THIS PRODUCT.  ALWAYS CONSULT A PHYSICIAN IF YOU HAVE ANY QUESTIONS ABOUT 

YOUR PHYSICAL ABILITY TO USE THIS PRODUCT.

• 

NEVER USE THIS TRIPOD WHILE TAKING DRUGS, ALCOHOL OR CERTAIN PRESCRIPTION DRUGS!  ALWAYS CONSULT A PHYSICIAN IF YOU 

HAVE ANY QUESTION ABOUT TAKING SPECIFIC MEDICATIONS AND USING THIS PRODUCT!

• 

NEVER USE THIS TRIPOD DURING INCLEMENT WEATHER SUCH AS RAIN, LIGHTNING, WINDSTORMS OR ICY CONDITIONS!  END YOUR 

HUNT AND RETURN TO THE GROUND IF ANY OF THESE INCLEMENT CONDITIONS ARISE.

• 

NEVER USE THIS TRIPOD WHEN FEELING ILL, NAUSEOUS, DROWSY OR DIZZY!

• 

BE WELL RESTED AND NEVER HURRY.  HURRYING CAUSES ACCIDENTS!

• 

CHECK EVERY COLUMN SECTION CONNECTION EVERY TIME YOU USE THE TRIPOD.  IF ANY COLUMN SECTIONS ARE SEPARATING - DO 

NOT USE THE TRIPOD!

• 

ALWAYS USE THE SUPPLIED SPIKES TO SECURE THIS TRIPOD TO THE GROUND BEFORE USE.

• 

NEVER SETUP OR USE THIS TRIPOD AROUND POWER LINES, POWER TRANSFORMERS, SUBSTATIONS OR POWER GENERATORS!

• 

CHECK THE GROUND UNDER THE TRIPOD TO MAKE SURE IT IS FIRM AND LEVEL.  SLOPING GROUND OR AN UNEVEN SURFACE (ONE 

COLUMN SECTION ON A ROCK FOR EXAMPLE) CAN CAUSE YOUR TRIPOD TO TILT OR SHIFT AS YOU CLIMB.

• 

PULL UP A BOW, BACKPACK, FIREARM OR OTHER EQUIPMENT ONLY AFTER BEING SECURE IN THE TRIPOD.  FIREARMS MUST BE PULLED 

UP UNLOADED, CHAMBER OPEN AND MUZZLE DOWN!

• 

NEVER MODIFY YOUR TRIPOD IN ANY WAY BY MAKING REPAIRS, REPLACING PARTS, OR ALTERING ADDING OR ATTACHING ANYTHING 

TO IT EXCEPT IF EXPLICITLY AUTHORIZED IN WRITING BY THE MANUFACTURER!

• 

INSTRUCTIONS (WRITTEN AND VIDEO) SHOULD BE KEPT IN A SAFE PLACE AND REVIEWED AT LEAST ANNUALLY.  IT IS THE RESPONSIBILITY 

OF THE TRIPOD OWNER TO FURNISH THE COMPLETE INSTRUCTIONS TO ANY PERSON WHO BORROWS OR PURCHASES THE TRIPOD!  THIS 

SUMMIT TRIPOD IS DESIGNED TO BE USED AS A COMPLETE SYSTEM - NEVER LOAN OR SELL ONLY A PORTION OF THIS TRIPOD.

• 

BEFORE EACH USE OF YOUR SUMMIT TRIPOD, ALWAYS INSPECT THE TRIPOD FOR ANY DAMAGE, CRACKS, TEARS, WEAR OR ABRASION 

THAT MAY HAVE OCCURRED IN TRANSPORTING / STORING YOUR TREESTAND.  DO NOT USE IF ANY DAMAGE IS FOUND!  CONTACT 

CUSTOMER SERVICE FOR THE APPROPRIATE REPAIR / REPLACEMENT PROCEDURE! 

• 

DO NOT LEAVE YOUR TRIPOD OUTDOORS WHEN IT IS NOT BEING USED!  ANY STAND TUBING THAT IS ALLOWED TO FILL WITH 

RAINWATER AND FREEZE WILL RUPTURE OR BURST - DO NOT USE YOUR TRIPOD IF THIS OCCURS!

• 

ALWAYS USE FOUR PEOPLE TO SETUP THIS TRIPOD!

Watchtower Tripod - 12’

PN 82072

Watchtower 12’ 82072, 1/2013

© 2013 Summit Treestands, LLC
715 Summit Dr. Decatur, AL 35601
(256) 353-0634
[email protected]
www.summitstands.com

INDEX

GENERAL WARNINGS AND PRECAUTIONS, TRIPOD WEIGHT LIMITS 

 

 

PG 1

SECTION 

INDEX 

        PG 

1

SECTION 

PARTS 

LIST 

        PG 

2

SECTION 

TOOLS 

REQUIRED 

       PG 

3

SECTION 

ASSEMBLY 

        PG 

12

SECTION 

SETUP 

AND 

USE 

       PG 

13

SECTION 6 - MAINTENANCE AND CARE   

 

 

 

 

 

PG 14

SECTION 7 - LIMITED WARRANTY INFORMATION 

 

 

 

 

PG 14

INSTRUCTIONS 

EN 

FRANÇAIS 

       PG 

15 

28

Summary of Contents for 82072





























Reviews: