manualshive.com logo in svg

Summerset SS-OVBI, Manual

Share
Download
Summerset SS-OVBI Manual Download Page 33

 

33 

 

The drip tray should be cleaned periodically 

according to the using situation

. 

 
NOTE: Allow the drip tray to cool before attempting to clean.

 

 

COOKING GRATES

 

 

The cooking grates can be 

cleaned immediately after cooking is completed and after turning 

off the oven. Wear a barbecue mitt and scrub the cooking grates with a damp cloth. If 

the oven 

is  allowed to cool down, cleaning the grates will be 

easier if removed from the oven

 and 

cleaned with a mild detergent.

 

 

STAINLESS STEEL

 

 

After initial usage, areas of the oven

 may discolor from the intense heat given off by the 

burners. 

This is normal. Purchase a mild stainless steel cleaner and rub in the direction of the grain of 

the metal. Specks of grease can gather on the surface of the stainless steel and bake on to the 

surface and give a

 worn appearance. For removal, use a non

-abrasive oven cleaner in 

conjunction with a stainless

 cleaner. 

 

NOTE: Always scrub in the direction of the grain.

 

 

GRILL LIGHT

 

 

Bulb Replacement

 

IMPORTANT SAFETY INSTRUCTIONS

 

Lighted lamp is HOT:

 

 

 

WARNING 

-TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO

 

EXCESSIVE UV RADIATION, OR INJURY TO PERSONS

.

 

 

1. Turn off/unplug and allow to cool before replacing bulb 

(lamp). 

2. Bulb (lamp) gets HOT quickly! Only contact switch/plug when turning on.

 

3. Do not touch hot lens, guard, or enclosure.

 

4. Do not remain in light if skin feels warm.

 

5. Do not look directly at lighted lamp.

 

6. Keep lamp away from materials that m

ay burn. 

7. Use only with a 10-watt or smaller bulb (lamp).

 

8. Do not touch the bulb (lamp) at any time. Use a soft cloth. Oil from skin may damage bulb

 

(lamp). 
9. Do not operate the portable luminaries with a missing or damaged guard, lamp containment

 

barrier, or UV filter. 

Summary of Contents for SS-OVBI


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands