background image

 

 

21 

WARNING  

Do not use the oven

 in garages, breezeways, sheds or any enclosed area.

 

Never operate the oven

 in enclosed areas as this could lead to a carbon monoxide buildup,

 

which could result in 

injury or death. Place the oven

 on a level surface. Avoid moving the 

oven while it is in operation.

 

 

NOTE: The oven

 will operate best if it is 

not facing directly into the wind

 

 

PREPARATION FOR NG CONVERSION:

 

 

Before beginning conversion, make sure all parts are present. Compare parts with package

 

contents. If any part is missing or damaged, do not attempt to convert. Contact customer

 

service for replacement parts.

 

1. Turn off gas supply, and then remove cap on gas supply side.

 

2. Recommended: Install a shut

-off valve on gas supply side before installing the socket.

 

3. Socket should be installed by an authorized technician in accordance with the n

ational 

fuel gas code (NFPA 54/ANSI223.1). 
4. Before inserting plug, turn on gas supply and leak test all connections including the stem 

of the shut-off valve and the opening of the socket. For best results, use an ammonia

-free 

soap and water solution.

 

NATURAL GAS INSTRUCTION:

 

 

1. To connect, push back socket 

sleeve (Fig. 1). 
2. Insert plug and release sleeve (Fig. 

2). 
3. Push plug until sleeve snaps 

forward (Fig. 3). (Gas will flow 

automatically. Failure to connect plug

 

properly to socket will inhibit ga

s flow 

to the appliance.)

 

4. Test connection with ammonia

-free 

soap and water

 solution. 

 

To disconnect

 

1. Pull sleeve back. Pull plug out of 

socket. (Gas is automatically shut off.)

 

2. Close shut-off valve and replace 

dust caps on socket

 and plug.

 

Fig. 3 

Socket

Sleeve

Sleeve

Socket

Fig. 2 

Fig. 1 

Socket

Sleeve

Plug

Summary of Contents for SS-OVBI


















































Reviews: