background image

Limited W

arranty SBB 137

T

rent Metals Limited warrants, on a limited basis, this fur-

nace to be free from defects in manufacturing as follows:

1. Heat exchanger is warranted for a period of ten years

as detailed below.

2. Electric controls and outside casing (or jacket) are

warranted for a period of 1 year from the date of
installation.

3. Furnace incorporating any of the below listed features

shall carry a 1 year warranty from date of installation
on this equipment:

a) Combustion air fan (in place of draft damper
motor), blower fan and motor.
b) Grates and shaking mechanism
c) Firebrick, providing it is properly installed and
not damaged by careless firing habits.

Heat Exchanger Limited 10 Y

ear Warranty

Cost to owner of r

eplacement heat exchanger expressed

as a percentage of the retail price in effect at the time of
shipment of the replacement heat exchanger.

*First 5 years after date of original installation
0% (replaced no charge)
*From year 5 through year 6

20%

*From year 6 through year 7

40%

*From year 7 through year 8

50%

*From year 8 through year 9

60%

*From year 9 through year 10

80%

*From year 10 and over

100%

The foregoing warranty applies only where installation
has been made in full accordance with Federal and Local
Laws and Codes or ordinances applying to installation of
Wood (or Coal) burning furnaces, and failure is not
caused by abuse, or failure to observe proper operating
instructions and cleaning suggestions accompanying the
furnace; furnace has been fired with the proper type of
fuel and maintained in accordance with our instructions;
furnace has not been fired at an input in excess of its
rated or designed capacity; furnace has been installed
where standard or normal atmosphere prevails and the
unit is not subject to excessive humidity, dust conditions,
or chemical atmosphere of any type or any kind which
may cause accelerated metal corrosion.

Warranty extends only to the repair or replacement of
parts returned, freight prepaid, to us, and which prove
defective after inspection and testing by us. Any labour
involved in effecting repair or replacement is excluded
from the warranty and Trent Metals Limited assumes no
responsibility for consequential damages of any kind to
persons or property.

The following forms part of this warranty and is intended
to elaborate on specific points of our Limited Warranty:
- Warranty on above units will be denied as per the fol-
lowing:
1. Rusting of the secondary heat exchanger where obvi-

ous cause is improper cleaning; particularly at the end
of each heating season to prevent damp creosote
from attacking the heat exchanger material: or, a
defective or improperly installed humidifier leaking
water onto the heat exchanger.

2. Warpage and cracking above the top row of firebrick.

Note: Your furnace requires periodic cleaning throughout

the heating season. Also - at the end of the heating
season your furnace must be completely cleaned
including all areas of the secondary heat exchanger
where creosote residue may accumulate and attract
moisture from damp basement areas.

Remember the warranty of this unit specified it covers
the materials and workmanship of the unit. It does not
cover damage resulting from improper firing practices
or maintenance procedures.

Annual oil burner service is required.

Please follow our instructions and keep your unit oper-
ating at peak efficiency and keep the warranty on your
unit valid.

A heat exchanger replaced under warranty, assumes only
the remaining unexpired portion of the 10 year warranty
period, determined by the date of original installation.

This is the only warranty applicable to Summeraire
Furnace.

Summary of Contents for SBB
















Reviews: