background image

                                                                                     

14 

                                                                                                                               

 

 
 

checking, tilt the snowblower onto its left side (opposite the oil filler neck). 
 
NOTE: Before placing the snowblower on its side, fully drain the fuel tank using 
a gas suction pump. Do not tilt the snowblower by more than 90 degrees. 
 

MAINTENANCE OF THE SPARK PLUG (FIG. 21) 

 
1. Once the engine has cooled, pull off the spark cover with a twist. 
2. Remove the spark plug using a spark plug wrench (not supplied). 
3. Clean the spark plug with a wire brush (not supplied). 
4. Using a feeler gauge, set the gap to 0.7~0.8mm. 
5. Install the spark plug carefully by hand, to

 

avoid cross-threading. 

6.  After  the  spark  plug  is  seated,  tighten  with  the  spark  plug  wrench  to 
compress the washer. 

 

 

ADJUSTING THE CONTROL CABLE 

 
Refer  to  Adjusting  the  Control  Cable  in  assembly.  See  Adjusting  the  Control 
Cable on page 6. 
 

INSPECTING THE AUGER PADDLE 

 
Service Interval: Yearly - Inspect the auger paddle and have the distributor or 
local agent replace the auger paddle and scraper if necessary. 
 
Inspect the auger paddle for wear. When a rotor blade edge has worn down to 
the  wear  indicator  hole,  have  the distributor  or  local  agent  replace  the  auger 
paddle and the scraper (Fig. 22). 
 

WARNING:

 If the wear indicator hole is intact, you don 't need to replace the 

auger paddle. If the wear indicator hole is exposed, replace the auger paddle 
and scraper. 

Summary of Contents for 0533201847ZB





















Reviews: