1. n
oteS
on
S
afety
1.1 g
enerAl
notes
on
sAfety
This operation manual is applicable for the machine USK
6-R. The machine may only be handled by personnel who
are qualified. Hold power tools by insulated gripping sur-
faces when performing an operation where the cutting
tool may contact hidden wiring or its own cord. Contact
with a «live» wire will make exposed metal parts of the tool
«live» and shock the operator.
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
1.2 u
se
of
the
mAchine
for
PurPoses
for
which
it
is
intended
The machine is intended for the cleaning, grinding and
polishing of metal with cleaning and non-woven brushes
and polishing rings without the use of water. The machine
is designed exclusively for a 2-hand application.
1.3 i
ncorrect
use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion
of
conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame
D-Bad Säckingen, 06/2017.
M. Voyame/Division manager
2. c
ommiSSioning
2.1 P
rior
to
tAKing
the
mAchine
into
serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool.
The power supply should not vary more than 10% above
or below the voltage indicated on the nameplate. Check
grinding tool prior to use. The grinding tool must be
mounted centrally and positioned against the limit stop.
The maximum allowable speed of the tool and of the
chuck may not be exceeded under any circumstances.
Observe national regulations. Remove safety guard.
2.2 t
AKing
the
mAchine
into
serVice
Preselect speed with adjusting wheel according to speed
table.
Level 1: 2800 min
-1
Level 4: 4500 min
-1
Level 2: 3300 min
-1
Level 5: 5100 min
-1
Level 3: 3900 min
-1
Level 6: 5900 min
-1
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t
urn
on
/t
urn
off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front unteil
it clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating
dAtA
Power voltage
230/240V/120V, 50/60Hz
Power Input 230/240V // 120V
1530W // 1340W
Power Output 230/240V // 120V
1000W // 800W
No-load speed
2800-5900 min
-1
Max. tool Ø
55mm
Pince de serrage Ø max.
12mm / 1/2“
Sound pressure level EN 60745
86dB(A), K=3dB
Noise emission level
97dB(A), K=3dB
Vibration EN 60745
5.3m/s
2
, K=1.5m/s
2
Weight w/o cable
2.9kg
Protection class
II
16
P
ortugúes
Español
Italiano
F
rançais
Deutsch
English
