SUHNER ABRASIVE TAM, Technical Document

Page: 21 / 60

CN
PL
CZ
FI
SE
NL
PT
ES
IT
Clean the spindle and all parts that must be installed.
Tighten firmly / loosen the grinding tool with an open end-
ed spanner. Follow these instructions in reverse order to
detach the grinding tool.
Use only those tools recommended by SUHNER.
You must also observe the safety instructions is-
sued by the manufacturer of the attachment.
You must check that the tools diameter is within the limits
and the max speed is higher than the tool’s idle or set
speed.
The tool must fit precisely in the receiver.
The installed attachment must be able to rotate freely. Af-
terwards a test run must be conducted without load for
at least thirty seconds. Vibrating tools must be replaced
immediately.
2.2 r
Ating dAtA
Connection G35
Maximum speed:
- Input TAM 1:1 / TAM 1:2
6'400min
-1 /
6'400min
-1
- Output TAM 1:1 / TAM 1:2 5'500min
-1 /
3'000min
-1
Gear i = TAM 1:1 / 1:2 1,16:1 / 2,16:11
Max. wheel diameter 150mm
Spindle thread M14 / 5/8"
Vibration EN 60745 5.1m/s
2
, K=1.5m/s
2
Weight 2.6kg
Max. water pressure
6bar
Driver 42V
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.3 O
perAting cOnditiOns
Temperature range during operation: 0 to +50°C
Relative air humidity: 95% at +10°C not condensed
3. h
aNDLINg
/o
PERaTIoN
3.1 w
Orking instructiOns
To achieve an optimum grinding result, move grinding
tool uniformly back and forth with light pressure.
Excessive pressure lessens the working capability of the
hand tool, as well as the life of the grinding tool.
3.2 s
witching
On/Off
Connect the water supply to the water stop on the hand
tool.
The max water pressure may not exceed 6 bar. If
this is not the case the customer must use a pres-
sure reducer.
Never operate the hand tool without water!
Hold the hand tool firmly.
The drive generates a high starting torque. This can lead
to unpredictable movements of the hand tool.
Switch on the drive.
Conduct the test run without load for at least thirty sec-
onds. Do not use vibrating grinding tools.
You must always hold the hand tool when it is operating.
Switch off the drive when you stop working. The tool still
needs time to stop after the tool has been switched off.
Put down the hand tool so that there can be no danger.
Remove the hand tool from the shaft.
4. S
ERvICE
/m
aINTENaNCE
4.1 p
reVentiVe mAintenAnce
Always keep the hand tool clean and in a dry
place.
4.2 r
epAir
If despite strict observance of the manufacturing and test-
ing method the hand tool should happen to fail, it must be
repaired by an authorized SUHNER agency.
4.3 w
ArrAnty
In the event of the tool being improperly handled, used
for purposes for which it is not intended and/or of the ser-
vice and maintenance instructions not being observed by
non-authorized persons, no warranty shall be in effect for
damages/consequential damages.
Complaints can only be honored if the hand tool is re-
turned in the undisassembled condition.
4.4 s
tOrAge
Temperature range during operation: -15°C to +50°C
Max. relative air humidity: 90% at +30°C, 65% at +50°C.
4.5 d
ispOsAl
/ e
nVirOnmentAl cOmpAtiBility
This hand tool consists of materials which can be dis-
FR
DE
21
EN